manualshive.com logo in svg

Perkins 1706EA-E93TA, Руководство по эксплуатации и обслуживанию, Страница: 135 / 140

Поделиться
Скачать
Perkins 1706EA-E93TA Скачать руководство пользователя страница 135

Index

A

Additional Messages ......................................... 7
After Starting Engine ....................................... 59

Extended Idle at Cold Ambient

Temperature............................................... 60

After Stopping Engine ..................................... 67
Air Compressor - Check (If equipped)............. 92
Air Shutoff - Test .............................................. 92
Air Tank Moisture and Sediment - Drain (If

Equipped) ...................................................... 92

B

Battery - Recycle ............................................. 93
Battery - Replace............................................. 93
Battery Disconnect Switch (If Equipped)......... 46
Battery Electrolyte Level - Check .................... 93
Battery or Battery Cable - Disconnect............. 94
Before Starting Engine .............................. 18, 56
Belt Tensioner - Check .................................... 94
Belts - Inspect/Adjust....................................... 95

Coolant Pump Drive Belt ............................. 95
Fan Belts...................................................... 95
New belts ..................................................... 96

Belts - Inspect/Adjust/Replace (Alternator

Belt) ............................................................... 96

Inspect ......................................................... 96

Belts - Inspect/Adjust/Replace (Fan Belts) ..... 96

Inspect ......................................................... 97

Belts - Replace ................................................ 97
Burn Prevention............................................... 13

Batteries....................................................... 13
Coolant ........................................................ 13
Diesel Fuel ................................................... 13
Engine and Aftertreatment System ............. 13
Oils............................................................... 13

C

Cold Weather Operation ................................. 68
Cold Weather Starting ..................................... 58

Ether Injection System (If Equipped)........... 58

Coolant (Commercial Heavy-Duty) -

Change .......................................................... 97

Drain ............................................................ 98
Fill ................................................................ 98
Flush ............................................................ 98

Cooling System Coolant (ELC) - Change ....... 99

Drain ............................................................ 99

Fill .............................................................. 100
Flush ............................................................ 99

Cooling System Coolant Level - Check......... 100
Cooling System Supplemental Coolant

Additive (SCA) - Test/Add............................ 101

Add the SCA, If Necessary ........................ 101
Test for SCA Concentration ....................... 101

Cooling System Water Temperature

Regulator - Replace..................................... 102

Crushing Prevention and Cutting Prevention.. 15
Customer Service.......................................... 132

D

DEF Filler Screen (Emission Related

Component) - Clean .................................... 102

DEF Manifold Filters (Emission Related

Component) - Replace ................................ 103

Type 1 Manifold ......................................... 103
Type 2 Manifold ......................................... 104

Diesel Exhaust Fluid (Emission Related

Component) - Fill ......................................... 105

Diesel Exhaust Fluid Filter (Emission

Related Component) - Replace................... 106

Diesel Exhaust Fluid Injector (Emission

Related Component) - Replace................... 108

Diesel Particulate Filter (Emission Related

Component) - Clean .................................... 108

Diesel Particulate Filter Regeneration ............ 61

Carbon Dioxide (CO

2

) Emissions

Statement................................................... 63

Regeneration ............................................... 61
Regeneration System Warning Indicators... 62
Regeneration Triggers ................................. 61

Driven Equipment - Check ............................ 108

E

Electrical System............................................. 19

Grounding Practices .................................... 19

Emissions Certification Film ............................ 34
Emissions Warranty Information ................... 130
Engaging the Driven Equipment ..................... 63
Engine - Clean............................................... 109

Aftertreatment ............................................ 109

Engine Air Cleaner Element - Replace ......... 109

Dual Element Air Cleaner ...........................110
Servicing the Air Cleaner Element ............ 109

M0087475-06

135

Index Section

Содержание 1706EA-E93TA













































































































































Отзывы:

Нет отзывов