Perkins 1706EA-E93TA Скачать руководство пользователя страница 95

Страница: 95 / 140

Remove the belt. Refer to Disassembly and
Assembly.

Note:

Note the belt position on the pulleys if the belt

is to be reused.

Ensure that the belt tensioner is securely installed.
Visually inspect the belt tensioner (1) for damage.
Check that the pulley on the tensioner rotates freely
and that the bearing is not loose.

i08390629

Belts

Inspect/Adjust

Note:

This

procedure

applies

engines

constant

speed

applications.

maximize

the

engine

performance,

inspect

the

belt

for

wear

and

for

cracking.

Replace

the

belt

the

belt

worn

damaged.

Fan

Belts

• Inspect each belt for cracks, splits, glazing,

grease, displacement of the cord and evidence of
fluid contamination.

Fan Belts Adjust

Illustration 78

g03748150

Typical example

Illustration 79

g03748169

Typical example

Loosen bolts (1) and (2), also loosen nut (3).

Loosen bolt (4) and nut (7).

Adjust nuts (5) and (7) in order to increase or
decrease the tension on union (6). This action will
tension the belts, the belts must be tensioned to

730 N (164 lb). To check accurately the belt tension,
a suitable gauge should be used.

Tighten nuts (5) and (7) securely. Tighten bolts (1)

and (2), also tighten nut (3). Tighten nut and bolts
to a torque of 89 N·m (65 lb ft). Tighten bolt (4) to
a torque of 100 N·m (73 lb ft).

Coolant Pump Drive Belt

• Inspect the belt for cracks, splits, glazing, grease,

displacement of the cord and evidence of fluid
contamination.

M0087475-06

Maintenance Section
Belts - Inspect/Adjust

Содержание 1706EA-E93TA












































































































































Результаты поиска

Содержание 1706EA-E93TA

Отзывы:

Perkins 1706EA-E93TA, Руководство по эксплуатации и обслуживанию, Страница: 95 / 140

Результаты поиска

Содержание 1706EA-E93TA

Отзывы: