Perkins 1103D Series Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 78

Perkins 1103D Series Скачать руководство пользователя страница 65

i02875191

Fuel

System

Primary

Filter

(Water

Separator

Element

-

Replace

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.

NOTICE

Do not allow dirt to enter the fuel system. Thoroughly
clean the area around a fuel system component that
will be disconnected. Fit a suitable cover over discon-

nected fuel system component.

Illustration 39

g01118416

Typical example

(1) Screw
(2) Element
(3) Glass bowl
(4) Sensor connection
(5) Drain
(6) Bottom cover

1.

Turn the fuel supply valve (if equipped) to the OFF

position.

2.

Place a suitable container under the water

separator. Clean the outside of the water
separator.

3.

Open the drain (5). Allow the fluid to drain into the

container.

4.

Tighten the drain (5) by hand pressure only.

5.

Hold the element (2) and remove the screw (1).

Remove the element and the glass bowl (3) from
the base. Discard the old element.

6.

Clean the glass bowl (4). Clean the bottom cover

(6).

7.

Install the new O ring seal. Install the bottom cover

onto the new element. Install the assembly onto
the base.

8.

Install the screw (1) and tighten the screw to a

torque of 8 N·m (6 lb ft).

9.

Remove the container and dispose of the fuel

safely.

10.

Open the fuel supply valve.

11.

Prime the fuel system. Refer to the Operation and

Maintenance Manual, “Fuel System - Prime” for
more information.

i02873572

Fuel

System

Secondary

Filter

-

Replace

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.

NOTICE

Do not allow dirt to enter the fuel system. Thoroughly
clean the area around a fuel system component that
will be disconnected. Fit a suitable cover over discon-

nected fuel system component.

SEBU8352-02

65

Maintenance Section

Fuel System Primary Filter (Water Separator) Element - Replace

«
...
63
64
65
66
67
...
»

Содержание 1103D Series















































































Отзывы:

Нет отзывов