PerkinElmer FT-IR Скачать руководство пользователя страница 1

Страница: 1 / 17

L1050070A

PerkinElmer Ltd, Chalfont Road, Seer Green,

Beaconsfield, BUCKS, HP9 2FX, United Kingdom.

Produced in the UK.

General Purpose Optical Bench w ith

External LiTaO

Detector Accessory

A Spectrum 100 Series or Spectrum 400 Series FT-IR instrument can be fitted with a General

Purpose Optical Bench. The optical bench is supplied with a parabolic mirror assembly, and an

external LiTaO

detector/pre-amplifier module. The optical bench is bolted to the external

accessory bracket, which is fitted in the handhold on the right of the instrument.

Figure 1 General Purpose Optical Bench with External LiTaO

Detector

This document describes how to:

•

Install a window in the right-hand external beam port;

•

Fit, and remove, the optical bench;

•

Fit the mirror and detector/pre-amplifier modules to the optical bench;

•

Configure Spectrum or Spectrum Express software to use an external detector;

•

Use Spectrum or Spectrum Express software to select the accessory;

•

Optimizing the performance of the detector/pre-amplifier;

•

Connect another type of detector/pre-amplifier to the instrument.

Optical bench

Mirror assembly

LiTaO3 detector /

pre-amplifier module

External

beam port

Fixing bolt

Fixing block

Содержание FT-IR


















Результаты поиска

Содержание FT-IR

Отзывы:

Похожие инструкции для FT-IR

Бренды по названию

Популярные бренды

PerkinElmer FT-IR, Руководство пользователя

Результаты поиска

Содержание FT-IR

Отзывы:

Похожие инструкции для FT-IR

Бренды по названию

Популярные бренды