6
7
SETUP - BEFORE USE
WARNING
Read the ENTIRE IMPOR-
TANT SAFETY INFORMATION section at
the beginning of this manual including all
text under subheadings therein before set
up or use of this product.
WARNING
TO PREVENT SERIOUS
INJURY FROM ACCIDENTAL OPERA-
TION: Release the trigger and unplug
the tool from its electrical outlet before
assembling or making any adjustments to
the tool.
NOTE
For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
INSTALLING THE AUXILIARY
HANDLES
WARNING
TO PREVENT SERIOUS
INJURY: Do not operate this tool without
an auxiliary handle properly installed.
The D-Handle (included) may be installed
for either right-hand or left-hand use.
Option 1: using with the D-handle
Attach the D-Handle to the sides of the
Front Cover, using the Hex Key and two
Hex Head Bolts.
Option 2: using with a Side handle (Side
handle not included).
WARNING
Read the ENTIRE IMPOR-
TANT SAFETY INFORMATION section at
the beginning of this manual including all
text under subheadings therein before set
up or use of this product.
INSTALLING THE BACKING
PAD/FOAM PAD
1. The accessory MUST be:
• Rated to at least 3000 RPM.
•
No larger than 7" (178 mm) in diameter.
• Fitted with a threaded opening
of 5/8" x 11 TPI.
• undamaged.
• a backing pad.
2. Press in and hold the Spindle Lock
Button to prevent the Spindle from
turning.
3. Thread the Backing Pad onto the Spindle
until firmly secured in place.
WORKPIECE AND WORK AREA SET UP
1. Designate a work area that is clean and
well-lit. The work area must not allow
access by children or pets to prevent
distraction and injury.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage. The
power cord must reach the work area
with enough extra length to allow free
movement while working.
3. Secure loose workpieces using a vise
or clamps (not included) to prevent
movement while working.
4. There must not be hazardous objects,
such as utility lines or foreign objects,
nearby that will present a hazard while
working.
POLISHING
1. Make sure the surface to polish has been
thoroughly washed, and is free of dust,
dirt, oil, grease, etc.
2. Place a clean Foam Pad (sold
separately) securely onto the Backing
Pad.
3. Apply about two tablespoons of wax (not
included) evenly on the clean Foam Pad.
CAUTION
Do not apply the wax directly
to the surface of the vehicle. The amount
of wax needed will vary according to the
size of the vehicle being waxed.
4. Rotate the Speed Dial to select the
desired speed between 1 and 4.
CAUTION
Only use the slower speeds
(1 through 4) for polishing. Otherwise,
damage may occur to the paint being pol-
ished. Performance Tool® is not respon-
sible for damage to the vehicle’s finish
due to improper use of this Polisher/
Sander.
OPERATION
5. If you are using one extension cord for more than
one tool, add the nameplate amperes and use the
sum to determine the required minimum cord size.
(See table a.)
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualified electrician before using it.
8. Protect the extension cords from sharp
objects,excessive heat, and damp or wet areas.
GROUNDING
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn
their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL DEFINITIONS
V
Volts
Voltage (Potential)
A
Amperes
Current
Hz
Hertz
Frequency (Cycles per Second)
W
Watt
Power
Kg
Kilograms
Weight
Alternating Current
Type of Current
Direct Current
Type of Current
Alternating or Direct Current
Type of Current
Earthing Terminal
Grounding Terminal
Class II Construction
Denotes Double Insulation
min
Minutes
Time
s
Seconds
Time
Ø
Diameter
Size of Drill Bits, Grinding Wheels, etc.
n
0
No load speed
No-load Rotational Speed
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3,...
Ring Selector Settings
Speed, Torque or Position Settings
Symbol
Name
Explanation
CONTROLS AND COMPONENTS
1. Backing Pad
2. Spindle Lock Cap
3. “D” Grip Handle
4. Speed Adjustment
5. Lock-on Button
6. Trigger Control
7. Carbon Brush Holder Cover
8. Spindle
1
2
3
5
6
7
8
4
Check out the collection of power tools we offer.
