10
CONTROL PANEL
USING THE CONTROL PANEL
COOL Mode
• Press the MODE button until the COOL indicator is on.
• Press the TEMP/TIME buttons (+/–) to adjust desired
room temperature on the display.
• Press the SPEED button to select desired fan speed
(High, Med, Low, Auto).
HEAT Mode
• Press the MODE button until the HEAT indicator is on.
• Press the TEMP/TIME buttons (+/–) to adjust desired
room temperature on the display.
• Press the SPEED button to select desired fan speed
(High, Med, Low, Auto).
FAN Mode
Use this mode to circulate the air in the room without
cooling or dehumidifying the room. In FAN mode, the
temperature cannot be adjusted.
• Press the mode button until the FAN indicator is on.
• Press the SPEED button to adjust the fan speed (High,
Med, Low). When using the control panel, AUTO fan
speed cannot be selected. AUTO fan speed can be
selected with the remote only.
ENERGY SAVER Mode
While the unit is running press the MODE button to select
ENERGY SAVER. When the set temperature is reached
the compressor will shut off. The fan will continue to run
3 minutes after the compressor shuts off. The unit will not
run for 10 minutes. After 10 minutes the fan will run for 1
minute and repeat the cycle. If the temperature changes, the
compressor will turn on until the set temperature is reached.
TIMER ON/OFF Function
TIMER ON
• Turn the unit on to set the desired temperature and fan
speed for when the unit turns on with the Timer.
• Turn the unit off (Standby).
• Press the TIMER button
• Press the TEMP/TIMER buttons (+/–) to set the time on
the display from 0.5–24 hours (by 0.5 hour increments up
to 24 hours).
• The TIMER ON/OFF indicator will be on when the timer
has been set.
TIMER OFF
• Turn the unit on to set the desired temp. and fan speed.
• Press the TIMER button.
• Press the TEMP/TIMER buttons (+/–) to set the time on
the display from 0.5–24 hours (by 0.5 hour increments up
to 24 hours).
• The TIMER ON/OFF indicator will be on when the timer
has been set.
NOTE:
To cancel the timer function press the TIMER button again.
Lights next to the touch pads on the unit's
control panel indicate the selected settings.
The display shows the set temperature when
in HEAT/COOL/ENERGY SAVER modes. The
display shows time remaining on the delay timer.
It shows the room temp. when in FAN only mode.
1. POWER Button
Press to turn the unit ON/OFF.
2. REMOTE CONTROL SIGNAL RECEIVER
• Make sure signal receiver is unobstructed.
• Maximum remote distance is 26 ft.
• Unit will beep when signal from remote has
been received.
3. DIGITAL DISPLAY
• In FAN mode, this displays the room temp.
• In COOL and HEAT mode, this displays the
set temperature.
• In TIMER function, On/Off time is displayed.
• If Display shows Error Codes, contact
Consumer Services at 844-472-2473.
4. SET Indicator
Light indicates the unit is in the temperature or
delay time set mode.
5. TEMP/TIMER B/–
• Press to adjust the temperature and set the
time for the On or Off timer.
• Press both + and – at the same time to
switch between °C and °F.
6. TIMER ON/OFF Indicator
Illuminates when timer has been set for On
and/or Off.
7. TIMER Button
Press to set the timer On/Off.
8. MODE Button
Press to select HEAT, COOL, ENERGY SAVER
or FAN.
9. FAN SPEED Button
Press to select LOW, MED, HIGH or AUTO
fan speed.
Set
+
-
TIMER
MED
HIGH
LOW
AUTO
POWER
FAN
SPEED
MODE
COOL
ENERGY SAVER
FAN ONLY
HEAT
0.5-24 HR
TEMP/TIMER
1
2
5
7
6
3
4
8
9
