8
Operation
10
Timer Set Control Buttons
For drier air, press the button and set to a lower percent value(%).
For damper air, press the button and set a higher percent value
(%).
Down/Up buttons
Humidity Set Control Buttons
The humidity level can be set within a range of 35%RH(Relative
Humidity) to 85%RH (Relative Humidity) in 5% increments.
When the unit is off, first press the Timer button, the TIMER ON
indicator light illuminates. It indicates the Auto Start program is
initiated. Press it againthe Time Off indecator light illuminates. It
indicates the Auto Stop is initiated.
Press or hold the UP or DOWN button to change the Auto time by
0.5 hour increments, up to 10 hours, then at 1 hour increments up to
24 hours. The control will count down the time remaining until start.
The selected time will register in 5 seconds and the system will
automatically revert back to display the previous humidity setting.
When the Auto start & Auto stop times are set, within the same
program sequence, TIMER ON OFF indicator lights illuminate
identifying both ON and OFF times are now programmed.
Turning the unit ON or OFF at any time or adjusting the timer setting
to 0.0 will cancel the Auto Start/Stop function.
When LED display window displays the code of P2, the Auto Start/
Stop function will also be cancelled.
Press to initiate the Auto start and Auto stop feature, in conjuction
with the and buttons.
Power button
Press to turn the dehumidifier on and off.
LED display
Shows the set % humidity level from 35% to 85% or auto start/stop time
(0~24) while setting, then shows the actual (±5% accuracy) room %
humidity level in a range of 30% RH(Relative Humidity) to 90%RH
(Relative Humidity).
Error Codes: AS- Humidity sensor error;
ES- Temperature sensor error;
Eb- Bucket is removed or not in right position--Replace the bucket in the
right position. (only available for the unit with pump feature).
Protection Codes:
P2- Bucket is full or bucket is not in right position--Empty the bucket and
replace it in the right position.(only available for the uint with no
pump feature.)
P2- Bucket is full -- Empty the bucket.(only available for the unit with
pump feature
with the and buttons. When the unit is on, first press the
Timer button, the Timer Off indicator light illuminates. It indicates
the Auto Stop program is initiated. Press it again the Time On
indecator light illuminates.It indicates the Auto Start is initiated.
11
NOTE:The indicator light illuminates when the function is selected.
Operation
Note: When one of the above malfunctions occurs, turn off the unit,
and check for any obstructions. Restart the unit, if the malfunction is
still present, turn off the unit and unplug the power cord. Contact
the manufacturer or its service agents or a similar qualified person
for service.
Removing the collected water
There are three ways to remove collected water:
1.Use the bucket
When the bucket is full, remover the bucket and empty it.
water outlet
NOTE: If the pump hose drops when you remove the bucket , you must
reinstall the pump hose properly to the unit before replace the bucket
into the unit.
2.Continuous draining
Water can be automatically emptied into a floor drain by attaching the
unit with a water hose (Id≥Φ 5/16",not included) with a female threaded
end (ID:M=1" , not included). (NOTE: On some models, the female
threaded end is included)
Pump hose
drops
Reinstall pump
hose properly
Water hose
Female
threaede
end
Remove the
plastic cover
by couter-clockwise
rotation.
NOTE: The pump operation on light blinks at 1Hz when the pump is
operational failure. Please turn off the unit and plug the power cord out.
Check the following things:
Cleaning the filter of the pump.
-Remove the bucket from the unit, take down the pump and clean the
filter of the pump.
-Check that the pump drain hose does not link or block.
-Empty the water of the bucket.
-Reinstall the pump hose if it drops and reinstall the bucket properly.
Turn on the unit. If the error repeats, call for service.
Remove the water hose and
reinstall the Plastic cover
3.Pump draining (on some models)
Water can be automatically emptied into a floor drain or a suitable
drainage facility by attaching the pump drain out with a pump drain hose
(od=Φ1/4" , supplied).
Insert pump
drain hose to
the drain hose
outlet
Pump drain
hose outlet
Pump drain hose
NOTE: The pump may cause big noise when it starts to work for 3~5
minutes. It is a normal phenomenon.
12
NOTE:
-Make sure the connection is tight and there is no leak.
-Lead the water hose to the floor drain or a suitable drainage facility,
the drainage facility and the water hose should be lower than the
drain outlet of the unit.
-Be sure to run the water hose sloping downward to let the water flow
out smoothly.
-When the continuous drain feature is not being used, remove the
drain hose from the outlet.
Maintenance
NOTE: Do not use this operation when the outdoor temperature is equal to
or less than 0°C (32°F), otherwise water tunrs into ice that will cause the
water hose blocked up and the unit failure. Make sure to empty the bucket
once a week when using the pump draining feature. When the pump
draining feature is not being used, remove the pump drain hose from the
outlet. Press the pump drain hose outlet in and take the pump drain hose
out from it . Make sure do not let the water in the pump hose drip to the floor.
Filter of the pump
2,Take the pump
drain hose out
1,Press the pump drain
hose outlet in
Press the power cord
buckle into the rear
cover.
Clean the bucket with water every few weeks.
Clean the filter with water at least every 30 days or
more often if necessary.
Care and cleaning of the dehumidifier
WARNING: Turn the dehumidifier off and remove the
plug from the wall outlet before cleaning.
1.Clean the bucket
2.Clean the air filter
3.Store the unit
When not using the unit for long time periods
-After turning off the unit, wait one day before emptying
the bucket.
-Clean the main unit, bucket and air filter.
-Wrap the cord and bundle it with the band.
-Cover the unit with a plastic bag.
-Store the unit upright in a dry, well-ventilated place.
CAUTION: DO NOT
operate the dehumidifier without
a filter because dirt and lint will
clog it and reduce performance.
Operation
13
Faults Diagnosis
Unit does not start
Water on floor
Frost appears on the coils
The unit makes a loud
noise when operating
Dehumidifier does not
dry the air as it should
-Make sure the dehumidifier s plug is pushed completely into the outlet.
-Check the house fuse/circuit breaker box.
-Dehumidifier has reached its preset level or bucket is full.
-Bucket is not in the proper position.
-The air filter is clogged.
-The unit is tilted instead of upright as it should be.
-The floor surface is not level.
-Hose to connector or hose connection may be loose.
-Intend to use the bucket to collect water, but the back drain plug is
removed.
-This is normal. The unit has Auto defrost feature.
-Did not allow enough time to remove the moisture.
-Make sure there are no curtains, blinds or furniture blocking the front or
back of the dehumidifier.
-The humidity selector may not be set low enough.
-Check that all doors, windows and other openings are securely closed.
-Room temperature is too low, below 5°C(41°F).
-There is a kerosene heater or something giving off water vapor in the room.
Please check the machine according to the following form before asking for maintenance:
Faults Diagnosis
What to check
Please request for repair if operate abnormally or does not operate, and the solutions above is useless.
