Pepperl+Fuchs VISIOLUX VB14 Series Скачать руководство пользователя страница 35

Страница: 35 / 38

Barcode Scanner VB14

TECHNICAL FEATURES

Subject to reasonable modifications due to technical advances.

Fuchs Group • Tel.: Germany (06 21) 7 76-0 • USA (330) 4 25 35 55 • Singapore 7 79 90 91 • Internet http://www.pepperl-fuchs.com

Note 1:

The features given are typical at a 25 *C ambient temperature (if not otherwise indicated).

Note 2:

Further details given in par. 3.3.

Note 3:

If the reader is used in high temperature environments (over 35 *C), use of the Beam-shutter is advised
(see the VisoSetup configuration program).

VB14

-300

-100

-440

-600

Aperature angle

60°

50°

USER INTERFACE

LED indicators

laser ON, good read, external trigger, data

tx/power ON

SOFTWARE FEATURES

READABLE CODE SYMBOLOGIES

• EAN/UPC

(including Add-on 2 and Add-on 5)

• 2/5 Interleaved

• Code 39 (Standard and Full

ASCII)

• Codabar

Other symbologies available on
request.

• Code 93

• Code 128

• EAN 128

• Pharmacode

CODE SELECTION

up to six different codes during
one reading phase

DECODING SAFETY

can enable multiple good reads
of same code

HEADERS AND TERMINATORS

up to four headers and four terminators

OPERATING MODES

On-Line, Automatic, Serial-On-Line, Test

CONFIGURATION MODES

• through menus using VisoSetup utility

• receiving commands from one of the

serial ports (HOST MODE)

PARAMETER STORAGE

Non-volatile internal EEPROM

ENVIRONMENTAL FEATURES

Operating temperature (Note 3)

0 to 40 °C (32 to 104 °F)

Storage temperature

-20 to 70 °C (-4 to 158 °F)

Humidity max.

90% non condensing

Vibration resistance

IEC 68-2-6 test FC 1.5 mm;
10 to 55 Hz; 2 hours on each axis

Shock resistance

IEC 68-2-27 test EA 30G;
11 ms; 3 shocks on each axis

Protection class

IP65

PHYSICAL FEATURES

Mechanical demensions

68 x 84 x 34 mm

Weight

300g.

330 g.

Содержание VISIOLUX VB14 Series







































Результаты поиска

Содержание VISIOLUX VB14 Series

Отзывы:

Похожие инструкции для VISIOLUX VB14 Series

Бренды по названию

Популярные бренды

Pepperl+Fuchs VISIOLUX VB14 Series, Руководство пользователя

Результаты поиска

Содержание VISIOLUX VB14 Series

Отзывы:

Похожие инструкции для VISIOLUX VB14 Series

Бренды по названию

Популярные бренды