Ultrasonic sensor
UC500-30GM-IUEP-IO-V15
3
R
e
le
ase
da
te:
20
1
3
-1
1-
2
2
1
0
:1
5
D
ate
of
i
ssue
: 20
1
3
-1
1-
2
2
1
9
1
2
3
8_e
ng
.xm
l
Germany: +49 621 776 4411
Fuchs Group
Refer to “General Notes Relating to Fuchs Product Information”.
USA: +1 330 486 0001
Singapore: +65 6779 9091
www.pepperl-fuchs.com
Description of Sensor Functions
Programming
The sensor is equipped with two outputs. Two trip points or trip values, as well as the output mode, can be programmed for each output. The
shape of the sensor sound cone can also be programmed. These parameters can be configured using two different methods:
- Using the sensor push buttons
- Using the IO-link interface of the sensor. This method requires an IO-link master (e.g. IO-link master01 USB) and the associated software.
The download link is available on the product page for the sensor with the IO link at www.pepperl-fuchs.de
Configuration using the push buttons is described below. To configure the parameters using the sensor IO-link interface, please read the software
description. The processes for configuring the trip points and the sensor operating modes run completely independently and do not influence one
another.
Note:
- The sensor can only be programmed during the first 5 minutes after switching on. This time is extended during the actual programming pro-
cess. The option of programming the sensor is revoked if no programming activities take place for 5 minutes. After this, programming is no
longer possible until the sensor is switched off and on again.
- The programming activities can be canceled at any time without changing the sensor settings. To do so, press and hold the push button for
10 seconds.
Programming the trip point/trip value of the analog characteristic
Note:
Each push button is assigned to a physical output. The switching output (C/Q) is programmed via push button T1. The analog output is program-
med via push button T2.
A flashing red LED during the programming process indicates unreliable object detection. Should this occur, correct the alignment of the object
until the yellow LED L1 or L2 flashes. Only then will the settings be transferred to the sensor memory.
Programming the trip points/trip values using the push button
Programming the near trip point/trip value of the analog characteristic
1. Position the object at the site of the required near trip point or trip value.
2. Press and hold the push button for 2 seconds (yellow LED flashes)
3. Briefly press the push button (green LED flashes 3 times as confirmation). The sensor returns to normal mode.
Accessories
BF 30
Mounting flange, 30 mm
BF 30-F
Mounting flange with dead stop, 30 mm
BF 5-30
Universal mounting bracket for cylindrical sensors with a diameter of 5 ... 30 mm
V15-W-2M-PUR
Female cordset, M12, 5-pin, PUR cable
V15-W-2M-PVC
Female cordset, M12, 5-pin, PVC cable
IO-Link-Master02-USB
IO-Link master, supply via USB port or separate power supply, LED indicators, M12
plug for sensor connection
IO-Link-Master-USB DTM
Communication DTM for use of IO-Link-Master
IODD Interpreter DTM
Software for the integration of IODDs in a frame application (e. g. PACTware)
PACTware 4.X
FDT-Framework
Microsoft .NET
UVW90-M30
Ultrasonic -deflector
UVW90-K30
Ultrasonic -deflector
DA5-IU-2K-V
Process control and indication equipment
1 BN
2 WH
3 BU
4 BK
5 GY
Wire colors in accordance with EN 60947-5-2
(brown)
(white)
(blue)
(black)
(gray)
