Germany: +49 621 776 4411
Fuchs Group
Refer to “General Notes Relating to Fuchs Product Information”.
USA: +1 330 486 0001
Singapore: +65 6779 9091
www.pepperl-fuchs.com
1
Ultrasonic sensor
UC500-30GM-IUEP-IO-V15
R
e
le
ase
da
te:
20
1
3
-1
1-
2
2
1
0
:1
5
D
ate
of
i
ssue
: 20
1
3
-1
1-
2
2
1
9
1
2
3
8_e
ng
.xm
l
Technical data
General specifications
Sensing range
30 ... 500 mm
Adjustment range
50 ... 500 mm
Unusable area
0 ... 30 mm
Standard target plate
100 mm x 100 mm
Transducer frequency
approx. 380 kHz
Response delay
Ex works settings:
≤
45 ms
configurable
Memory
Non-volatile memory
EEPROM
Write cycles
100000
Indicators/operating means
LED green
solid: Power on
flashing: Standby mode or IO link communication
LED yellow 1
solid: Object in evaluation range
flashing: Learning function, object detected
LED yellow 2
solid: Object in evaluation range
flashing: Learning function, object detected
LED red
solid red: Error
red, flashing: program function, object not detected
Electrical specifications
Operating voltage U
B
10 ... 30 V DC , ripple 10 %
SS
15 ... 30 V voltage output
No-load supply current I
0
≤
60 mA
Power consumption P
0
≤
1 W
Time delay before availability t
v
≤
100 ms
Interface
Interface type
IO-Link
Protocol IO-Link
V1.0
Transfer rate
Acyclical: typical 240 Bit/s
Cycle time
min. 13.2 ms
Mode
COM 2 (38.4 kBaud)
Process data witdh
16 bit
SIO mode support
yes
Input/Output
Input/output type
1 synchronization connection, bidirectional
0 Level
0 ... 1 V
1 Level
4 V ... U
B
Input impedance
> 12 k
Ω
Output rated operating current
< 12 mA
Pulse length
0.5 ... 300 ms (level 1)
Pulse interval
≥
14 ms (level 0)
Synchronization frequency
Common mode operation
≤
70 Hz
Multiplex operation
≤
90 Hz / n , n = number of sensors , n
≤
10
(factory setting: n = 5 )
Output
Output type
1 push-pull (4 in 1) output, short-circuit protected, reverse
polarity protected
Current output 4 mA ... 20 mA or
voltage output 0 V ... 10 V configurable
Rated operating current I
e
200 mA , short-circuit/overload protected
Voltage drop U
d
≤
2.5 V
Resolution
current output: evaluation range [mm]/3200 but
≥
0.05 mm
voltage output: evaluation range [mm]/4000 but
≥
0.05 mm
Deviation of the characteristic curve
≤
0.2 % of full-scale value
Repeat accuracy
≤
0.1 % of full-scale value
Switching frequency f
≤
11 Hz
Range hysteresis H
1 % of the adjusted operating range (default settings),
programmable
Load impedance
current output:
≤
300 Ohm
Voltage output:
≥
1000 Ohm
Temperature influence
≤
1.5 % from full-scale value (with temperature
compensation)
≤
0.2 %/K (without temperature compensation)
Ambient conditions
Ambient temperature
-25 ... 70 °C (-13 ... 158 °F)
Storage temperature
-40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type
Connector M12 x 1 , 5-pin
Protection degree
IP67
Material
Housing
Stainless steel 1.4305 / AISI 303
TPU
Polyamides
Transducer epoxy
resin/hollow
glass sphere mixture; polyurethane foam
Mass
66 g
Factory settings
Output 1
near switch point: 50 mm
far switch point: 500 mm
output function: Window operation mode
output behavior: NO contact
Model Number
UC500-30GM-IUEP-IO-V15
Single head system
Features
• IO-link interface for service and
process data
• Programmable via DTM with
PACTWARE
• Switch output and analog output
• Selectable sound lobe width
• Latching mode selectable
• Window function can be selected
• Synchronization options
• Temperature compensation
Diagrams
200
150
100
50
0
-50
-100
-150
-200
X
Y
Characteristic response curve
Distance X [mm]
Distance Y [mm]
flat surface
100 mm x 100 mm
round bar, Ø 25 mm
wide sound lobe
narrow sound lobe
0 100
200
300
400 500 600 700 800 900
1000
1100
