Pepperl+Fuchs KFD2-SR3-2.2S Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

Pepperl+Fuchs KFD2-SR3-2.2S Скачать руководство пользователя страница 14

20

16-03

14

Functional Safety KFD2-SR3-(Ex)2.2S

Mounting and Installation

4

Mounting and Installation

Installing the device
1. Observe the safety instructions in the instruction manual.
2. Observe the information in the manual.
3. Observe the requirements for the safety loop.
4. Connect the device only to devices that are suitable for this safety application.
5. Check the safety function to ensure the expected output behavior.

4.1

Configuration

Configuring the Device
The device is configured via DIP switches. The DIP switches for setting the safety

functions are on the front of the device.

1. De-energize the device before configuring the device.
2. Open the cover.
3. Configure the device for the required safety function via the DIP switches,

see chapter 3.3.

4. Close the cover.
5. Secure the DIP switches to prevent unintentional adjustments.
6. Connect the device again.

Note!

For more information see the corresponding datasheets.

Functional Safety KFD2-SR3-(Ex)2.2S

«
...
12
13
14
15
16
...
»

Содержание KFD2-SR3-2.2S





















Отзывы:

Нет отзывов