Pepperl+Fuchs IC-KP2-1HB6-2V15B Скачать руководство пользователя страница 77

Страница: 77 / 80

IC-KP2-1HB6-2V15B

Fault location

13-

Fault location

Fault source

Possible cause

Remedy

The operating voltage LED

(PWR/ERR) does not light

up.

The power supply is not

connected properly.

Ensure that the power

supply is connected to a

24 V DC source.

The CH1 indicator does not

light up even though the

R/W head is connected to

port 1.

The cable is defective or

not connected correctly.

Check the cable and repair

if necessary.

The R/W head is defective.

Check the R/W head and

replace if necessary.

A read command (e.g.

...) gives the status 4

even though the syntax is

correct.

An incorrect data carrier

type is selected for the

relevant channel (e.g.

IPC02). The read

commands only function

with data carriers and not

with code carriers.

Preset the correct data

carrier type (e.g. IPC03) or

"Autodetect" using the

... command.

The LEDs in the reading

head and the CHx indicator

on the IDENTControl are

flashing.

The connected reading

head does not support the

preset data carrier type.

Select a data carrier type

that the reading head

supports.

The

command

(get configuration) gives the

status 4 even though the

syntax is correct.

IPC03 is not selected for

the relevant channel. The

configuration commands

only function if the data

carrier IPC03 is selected

and not in autodetect

mode.

Preset the data carrier type

IPC03 using the

...

command.

The red "BusError" LED

lights up (slave is not in

"DataExchange" state).

There is no longer a

connection to the master.

Check the cable, the

connection and the

terminator and repair if

necessary.

The slave address is

incorrect.

Configure the device and

the master with the same

slave address (on the

slave in the hexadecimal

display).

Table 9.1

This table will be updated and extended if necessary.

Visit www.pepperl-fuchs.com to view the latest version of the manual.

Содержание IC-KP2-1HB6-2V15B

















































































Результаты поиска

Содержание IC-KP2-1HB6-2V15B

Отзывы:

Бренды по названию

Популярные бренды

Pepperl+Fuchs IC-KP2-1HB6-2V15B, Руководство пользователя

Результаты поиска

Содержание IC-KP2-1HB6-2V15B

Отзывы:

Бренды по названию

Популярные бренды