Pentax K10D 76830 Скачать руководство пользователя

Страница: 40 / 69

20. 0-A51(Tripod plate)

①

0-A51

②

CNL-D1.7x2.5 x4

③

Arrange lead wires as shown figure.

（

S300 and T770

）

21. [Adjustment] Initialization when replacing T100

[Caution]

When replacing T100, you must execute this initialization. Do not execute with other reason.

[Required equipment]

SD card

SD card 2 pieces (FW for replacing T100, for install initial data), TV monitor, Exclusive

Video cable, Circuit tester, AC adaptor (or DC cord for 76830, Power supply DC8.3V/3A or above)

21-1. Preparation

①

Connect the TV monitor by Video cable.

②

Solder main switch land on T200.

21-2. Power check

①

Connect to the power supply by DC cord and set DC8.3V/3A.

②

Connect the DC cord to the camera. Confirm that there is no short circuit or leak.

[Caution]

If there is short circuit, disconnect the power immediately.

With this condition battery current is approx.320mA (metering switch off).

③

Disconnect DC cord.

21-3. Installing FW for replacing T100

[Caution]

All setting will be cleared

①

Connect the Video cable and AC adaptor to the camera.

②

Surely install SD card (FW for replacing T100) to the card slot.

③

TV monitor will be displayed as right Fig.

If you cancel installation, disconnect AC adaptor first then remove SD card.

④

When [>>> EJECT SD CARD <<<] is displayed, remove the SD card.

Installation will be started. It takes approx.90sec. (UPDATING…)

[Caution]

Do not turn OFF the power.

⑤

When [POWER OFF] is displayed, disconnect AC adaptor.

*leave the video cable.

①

②

DT(4x15)

DT(4x10)

②

DETECTED BOTH F/W FILE

NOW LOADING

DETECTED FIRMWARE FILE

COMPLETE LOADING

-------

CPU

--------

CURRENT VER.1.00.00.00
UPDATE VER.1.00.00.10

=======

DSP

========

CURRENT VER.1.00.00.00
UPDATE VER.1.00.00.10

>>> EJECT SD CARD <<<

SAMSUNG GX10

UPDATING DSP FIRMWARE

SECTOR** >>

PROGRAM

_____________

NEVER POWER OFF

SAMSUNG GX10

UPDATING DSP FIRMWARE

**** COMPLETE ****

VERSION 1.00.00.10

POWER OFF

Main SW

Land

Содержание K10D 76830






































































Результаты поиска

Содержание K10D 76830

Отзывы:

Похожие инструкции для K10D 76830

Бренды по названию

Популярные бренды

Pentax K10D 76830, Руководство по обслуживанию

Результаты поиска

Содержание K10D 76830

Отзывы:

Похожие инструкции для K10D 76830

Бренды по названию

Популярные бренды