Pentax K10D 76830 страница 25 Скачать руководство пользователя

Страница: 25 / 69

8. [ADJ] AF Joint stroke

[Required equipment]

Vernier calipers

①

Set the AF lever (0-A115) to the AF.C position.

②

AF coupler(0-S300) must be projected from

the mount surface by 1.2mm or more.

③

When the mount lock pin comes to the mount surface

with depressing the mount lock lever, the AF coupler

must not be projected out of the mount surface.

④

Adjust 0-A121 by turning an eccentric screw,
and apply the screw lock.

9. L2 and 0-L3

[Caution]

Confirm there is neither dust nor scratch on L2 and 0-L3.

①

②

0-L3

③

Tighten M16 (Adjustment screw) temporary

while pushing 0-L3 front side.

④

Down the focusing screen frame (0-M4) by releasing the hook portion.

⑤

Push the arrow part in figure and install M22.

In the case of temporary adjustment, Using with the M22-00E(0.35).

⑥

Put the focusing screen (L2) on the frame and then push it back until it locks in place.

10. M301

①

Eyepiece (M301,L7 and other)

②

TY-CNL-D1.7x4.0

（

）

④

⑤

⑥

①

②

①

②

③

④

①

②

③

Содержание K10D 76830






































































Результаты поиска

Содержание K10D 76830

Отзывы:

Похожие инструкции для K10D 76830

Бренды по названию

Популярные бренды

Pentax K10D 76830, Руководство по обслуживанию

Результаты поиска

Содержание K10D 76830

Отзывы:

Похожие инструкции для K10D 76830

Бренды по названию

Популярные бренды