manualshive.com logo in svg

Pentair MASTERTEMP 125, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pentair MASTERTEMP 125 Скачать руководство пользователя страница 18

P/N 475114 Rev. F  8/2020

 

MASTERTEMP 125 Pool and Spa Heater Installation and User’s Guide

|   9

OUTDOOR HEATER INSTALLATION 

 

The following information is for heaters located outdoors, using the built-in stackless venting system.

WARNING

CARBON MONOXIDE GAS IS DEADLY – 

Exhaust from this pool heater contains carbon monoxide, a dangerous, poisonous 

gas you cannot see or smell.  Symptoms of carbon monoxide exposure or poisoning include dizziness, headache, nausea, 
weakness, sleepiness, muscular twitching, vomiting and inability to think clearly. IF YOU EXPERIENCE ANY OF THE ABOVE 
SYMPTOMS, IMMEDIATELY TURN OFF THE POOL HEATER, LEAVE THE VICINITY OF THE POOL OR SPA AND GET INTO 
FRESH AIR IMMEDIATELY. THE POOL HEATER MUST BE THOROUGHLY TESTED BY A GAS PROFESSIONAL BEFORE 
RESUMING OPERATION.

EXCESSIVE CARBON MONOXIDE EXPOSURE CAN CAUSE BRAIN DAMAGE OR DEATH.

Locate the heater in an open, unroofed area and on a level 

surface that is protected from drainage or run-off. Install the 

heater in an area where leaves or other debris will not collect 

on or around the heater. 

It is recommended that a non-combustible base be a platform under 

the heater constructed of hollow masonry blocks, not less than 

 

100 mm (4 in) thick (laid with ends unsealed and joints 

matched for air circulation). Cover blocks with 0.75 mm (0.03 

in) minimum galvanized sheet metal, see Figure 11.
To avoid damage to the electronic components in the heater, 

take care to prevent prolonged exposure to driving sources 

of water (such as lawn sprinklers, heavy roof runoff, hoses, 

etc.). Avoid operation in persistent, extreme, moist or salty 

environments.

In extreme weather, shut down the heater and disconnect the 

power to it until the weather has moderated. In areas subject to 

hurricanes or very high winds, purchase the Bolt Down Bracket 

Kit, P/N 460738, see Figure 12. 

Lead

Anchor

For Heater mounting
bolts and clamps, 
purchase separately
Bolt Down Bracket Kit, 
Part No. 460738.

SHEET
METAL

BLOCKS

Hollow masonry blocks, not less than 100 mm (4 in) thick, (laid with ends unsealed and joints

matched for air circulation). Cover blocks with 0.75 mm (0.03 in) minimum) galvanized sheet metal.

150 mm

(6 in) Min.

BASE FOR USE ON
COMBUSTIBLE
FLOORS

Masonry blocks, 

not less than 100 mm (4 in) thick

150 mm

(6 in) Min.

WARNING

Risk of explosion if a unit burning propane gas is installed in a pit or other low spot.

 Propane is heavier than air. Do not 

install the heater using propane in pits or other locations where gas might collect. Consult the European Standard Codes of 
Practice

 

building code officials to determine installation requirements and specific installation restrictions of the heater relative 

to propane storage tanks and filling equipment. Installation must meet the requirements for the Standard for the Storage and 
Handling of Liquid Petroleum Gases.

 

Consult local codes and fire protection authorities about specific installation restrictions.

Figure 12.

Figure 11.

Section 1. Installation 

Содержание MASTERTEMP 125





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды