manualshive.com logo in svg

Pentair MASTERTEMP 125, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pentair MASTERTEMP 125 Скачать руководство пользователя страница 14

P/N 475114 Rev. F  8/2020

 

MASTERTEMP 125 Pool and Spa Heater Installation and User’s Guide

|   5

 
 
 
BELOW POOL INSTALLATION

 

If the heater is below water level, the pressure switch must be adjusted. This adjustment must be done by a qualified 

service technician. 

See following CAUTION before installation.

CAUTION 

BELOW OR ABOVE POOL INSTALLATION

The WATER PRESSURE RELIEF VALVE SWITCH is set in the factory at 0.20 bar (3.00 psi). This setting is for a heater 
installed at pool level. If the heater is to be installed more than 1’ above or below, the water pressure switch must be 
adjusted by a qualified service technician. See page 39.

FLOW SWITCH INSTALLATION

If the heater is installed more than 1.5 m above the pool or more than 1.2 m below the pool level, which is beyond the 
limits of the heater’s pressure switch specification. In this case, a flow switch must be installed in the heater. Locate 
and install the flow switch externally on the outlet piping from the heater, as close as possible to the heater. Connect 
the flow switch wires as used for the water pressure switch.

VALVES

 

When any equipment is located below the surface of the pool or spa, valves should be placed in the circulation piping 

system to isolate the equipment from the pool or spa. Check valves are recommended to prevent back-siphoning.  

Back-siphoning is most likely to occur when the pump stops, creating a pressure-suction differential. Do 

NOT

 sanitize the 

pool by putting chlorine tablets or sticks into the skimmer(s). When the pump is off, this will cause a high concentration 

of chlorine to enter the heater, which could cause corrosion damage to the heat exchanger.

CAUTION

Exercise care when installing chemical feeders so as to not allow back siphoning of chemical into the heater, filters or 
pump. When chemical feeders are installed in the circulation of the piping system, make sure the feeder outlet line is 
down stream of the heater, and is equipped with a positive seal  noncorrosive “Check Valve”, (P/N R172288), between 
the feeder and heater.

MANUAL BY-PASS 

(WATER FLOW RATE)

 

Where the water flow rate exceeds the maximum 454 L/m, a manual 

byp

ass should be installed and adjusted.  After installing the valve, adjust 

the valve to bring the flow rate within the acceptable range. Then remove 

the valve handle or lock it in place to avoid tampering. See Figure 7

.

Table 1.

See page 39 for Pressure Relief Valve installation.

Cool water in

Warm water out

OUTLET TO POOL

INLET FROM HEATER

1. Set Manual By-Pass Valve.
2. Remove Handle.

Figure 7.

Model

Min. L/m (GPM) 

Max. L/m (GPM) *

125

76 (20)

265 (70)

* DO NOT EXCEED THE MAXIMUM RECOMMENDED FLOW RATE 

FOR THE CONNECTING PIPING.

Section 1. Installation 

Содержание MASTERTEMP 125





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды