manualshive.com logo in svg

Pentair MASTERTEMP 125, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pentair MASTERTEMP 125 Скачать руководство пользователя страница 1

MASTERTEMP

™

125 POOL AND SPA HEATER (EURO)

  

  

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity 

of this or other appliances.

FOR 

YOUR 

SAFETY

 

 

       Improper installation, adjustment,  

 

 

       alteration, service or maintenance 

can cause property damage, personal injury or death. 

Installation and service must be performed by a

 

qualified installer, service agency or the gas supplier.

• 

Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any phone in your building.

•  Immediately call your gas supplier from a neighbor’s phone.

 

Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire department.

FOR YOUR  SAFETY

 - This product must be installed and serviced by authorized personnel, qualified in pool/spa 

heater installation. Improper installation and/or operation can create carbon monoxide gas and flue gases which can 
cause serious injury, property damage, or death. For indoor installations, as an additional measure of safety, Pentair 
Water Pool and Spa strongly recommends installation of suitable 

Carbon Monoxide Detectors

 in the vicinity of this 

appliance and in any adjacent occupied spaces. Improper installation and/or operation will void the warranty.

FOR YOUR SAFETY - READ BEFORE OPERATING

If you do not follow these instructions exactly, a fire or explosion may result, causing 

property damage, personal injury or loss of life. For additional free copies of this 

manual; call USA (800) 831-7133.

 

OWNER:  

Retain For

Future

Reference

MT125, EURO         461078                  461079 
MT125HD, EURO    460902                  460903

INSTALLATION AND USER’S GUIDE

Pentair Water Pool and Spa, Inc. EMEA:  Head Office: Industriepark, Wolfstee, Toekomstlaan 30, 2200 Herentals - Belgium.
Pentair Water Pool and Spa, Inc. USA: 

1620 Hawkins Ave., Sanford, NC 27330, USA • (919) 566-8000 • (800) 831-7133

 

 

 

 

10951 W. Los Angeles Ave., Moorpark, CA 93021, USA • (805) 553-5000 • (800) 831-7133 

0087

1312 

COUNTRY OF DESTINATION:

GB, BE, FR, DE

•    If you do not follow these instructions exactly, a fire or explosion may result, causing property    
     damage, personal injury or loss of life.
•    Improper installation, adjustment, alteration, service or maintenance can cause property  

 

     damage, personal injury or death.  Installation and service must be performed by a qualified    
     installer, service agency or the gas supplier.
•    Do not place articles or against this appliance.
•    Do not use or store flammable materials near this appliance.
•    Do not spray aerosols in the vicinity of this appliance while it is in operation.

FOR YOUR SAFETY

www. pentaireurope.com - www.pentairwater.com.au - www.pentairpool.com - www.staritepool.com

WHAT TO DO IF YOU SMELL GAS

NOx CLASS 5

    Models             Natural Gas        Propane Gas 
  (240 VAC)            (G20 , G25)              (G31)

Содержание MASTERTEMP 125





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды