Pentair FLECK 9000 SXT Скачать руководство пользователя

Страница: 60 / 118

Installer manual Fleck 9000 SXT - Programming

60 / 118

Ref. MKT-IM-020 / C - 21.11.2019

6.5.14

Flow meter type (FM)

Select the flow meter type.

Options:

• P0.7: ¾" paddle wheel meter (Standard setting for 4600, 5600 and 9100);

• t0.7: ¾" turbine meter;

• P1.0: 1" paddle wheel meter (Standard setting for 2750 and 9000);

• t1.0: 1" turbine meter;

• P1.5: 1½" paddle wheel meter (Standard setting for 2850);

• t1.5: 1½" turbine meter;

• P2.0: 2" paddle wheel meter;

• Gen: generic or other non-Fleck meter.

1. Press

to set the flow meter type.

2. Press

to validate the selection and move to the next

parameter or exit master programming mode and save
modifications done.

Содержание FLECK 9000 SXT























































































































Результаты поиска

Содержание FLECK 9000 SXT

Отзывы:

Похожие инструкции для FLECK 9000 SXT

Бренды по названию

Популярные бренды

Pentair FLECK 9000 SXT, Руководство по установке

Результаты поиска

Содержание FLECK 9000 SXT

Отзывы:

Похожие инструкции для FLECK 9000 SXT

Бренды по названию

Популярные бренды