background image

Disinfection Of Water Conditioners

The materials of construction of the modern water conditioner 

will not support bacterial growth, nor will these materials 

contaminate a water supply. During normal use, a conditioner 

may become fouled with organic matter, or in some cases with 

bacteria from the water supply. This may result in an off-taste 

or odor in the water.
Some conditioners may need to be disinfected after 

installation and some conditioners will require periodic 

disinfection during their normal life.
Depending upon the conditions of use, the style of conditioner, 

the type of ion exchanger, and the disinfectant available, a 

choice can be made among the following methods.

Sodium or Calcium Hypochlorite Application

These materials are satisfactory for use with polystyrene 

resins, synthetic gel zeolite, greensand and bentonites.

5.25% Sodium Hypochlorite

These solutions are commonly known as household bleach. 

If stronger solutions are used, such as those sold for 

commercial laundries, adjust the dosage accordingly.
1.  Dosage

F. Polystyrene resin; 1.2 fluid ounce (35.5 ml) per  

cubic foot.

G.  Non-resinous exchangers; 0.8 fluid ounce (23.7 ml) per 

cubic foot.

2.  Brine tank conditioners

A.  Backwash the conditioner and add the required amount 

of hypochlorite solution to the well of the regenerant 

tank. The regenerant tank should have water in it to 

permit the solution to be carried into the conditioner.

B.  Proceed with the normal regeneration.

Calcium Hypochlorite

Calcium hypochlorite, 70% available chlorine, is available in 

several forms including tablets and granules. These solid 

materials may be used directly without dissolving before use.
1.  Dosage

A.  Two grains (approximately 0.1 ounce [3 ml]) per  

cubic foot.

2.  Regenerant tank conditioners

A.  Backwash the conditioner and add the required amount 

of hypochlorite to the well of the regenerant tank. The 

regenerant tank should have water in it to permit the 

chlorine solution to be carried into the conditioner.

B.  Proceed with the normal regeneration.

SERVICE AND MAINTENANCE 

CONTINUED

 

AUTOTROL

®

 740/760 Control 255 & Performa Series Valves (268, 268FA) Service Manual 

 

29

Содержание AUTOTROL 740

















































Отзывы: