Pentair 75, Руководство по эксплуатации и установке

Страница: 6 / 24

6
P/N 471105 Rev. F 1-22-04
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set the thermostat to the lowest setting.
3. Turn off all electric power to the heater.
4. Remove the control access door.
5. Push in the gas control valve slightly and turn clockwise
to "OFF"; see Figure 2.
6. The knob cannot be turned from "PILOT" to "OFF" unless the knob is
pushed in slightly.
Do not force .
7. Wait five (5) minutes to clear out any gas. If you then smell gas, STOP ! Follow "B" in the
safety information above. If you don't smell gas, go to next step.
8. Turn the knob on the gas control to counterclockwise to "PILOT"; see Figure 3.
9. Push the control knob all the way and hold in. Immediately light the pilot with
Presslite matchless ignition system by pressing the red igniter button, (located at
panel next to the gas valve). Continue to hold the control knob in for about (1)
minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 4 through 7.
10. If the knob does not pop up when released, stop and immediately call your service
technician or gas supplier.
11. If the pilot, see Figure 4, will not stay lit after several tries, turn the gas control knob
to "OFF" and call your service technician or gas supplier.
12. Turn the gas control knob counterclockwise to "ON".
13. Replace the control access door.
14. If the heater will not operate, follow the instructions "To Turn Off Gas To Heater"
and call your service technician or gas supplier.
TO TURN OFF GAS TO HEATER
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the heater if service is to be performed.
3. Remove control access door.
4. Turn gas control lever horizontally to "OFF".
Do not force.
5. Replace control access door.
Operation (contd.)
MILLIVOLT LIGHTING/OPERATION- NATURAL GAS & PROPANE
FOR YOUR SAFETY: READ BEFORE LIGHTING
Figure 4.
PILOT ADJ
IN
ON
OFF
VENT
TH
TP
TH
TP
A. This heater has a pilot that must be lit manually. When
lighting the pilot follow these instructions exactly.
B. BEFORE LIGHTING smell all around the heater area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any heater.
- Do not touch any electric switch; do not use any phone
in your building.
- Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
- If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it. Call a qualified service
technician. Forced or attempted repair may result in a
fire or explosion.
D. Do not use this heater if any part has been under water.
Immediately call a qualified service technician to inspect
the heater and to replace any part of the control system
and any gas control which has been under water.
Figure 3.
WARNING
If you do not follow these instructions exactly, a fire or explosion may result causing personal injury,
loss of life and property damage.
Since propane gas is heavier than air, escaping propane will accumulate and remain at ground level. Do
not attempt to light the heater. If you suspect a propane leak, lighting the heater can result in a fire or
explosion which can cause personal injury, death, and property damage.
Figure 2.
(Robertshaw valves)
(SIT valve)
All Gas knob's shown
in "OFF" position.