PEMTECH PT800 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

PEMTECH PT800 Series Скачать руководство пользователя страница 7

2.1 Programming Gateway Station ID #

Each gateway that needs to send data to the main control panel must be configured with a
station ID number. Each Gateway uses this distinct ID number to identify itself to PT2000
Series Main Control Panel. All the Gateways on the network must have a unique station ID #.
That is no two gateways shall have the same Station ID. Since each gateway is a dual channel
the data transmitted to the main control panel in a 2 sensor data block format. Thus
detectors connected to Station1 would be identified as detector 1 and 2; for Station2
detectors would be identified as # 3 and #4 and so.

Thus for 24 Channel PT2000 Series control panel up to 12 Gateways can be installed on the
network.

Internal Magnetic Switch – 1
To Set Station # and Zone ID

Internal Magnetic Switch – 2
To Set Channel / Sensor Type &
Low & Hi Alarm Levels

Figure 3. Sensor Interface and Control Module

7

Operators Manual Dual Channel Wireless Gateway Rev 1. Feb 2014

«
...
5
6
7
8
9
...
»

Содержание PT800 Series

















Отзывы:

Нет отзывов