Pella 80KM0103 Скачать руководство пользователя страница 3

SETTING AND FASTENING THE DOOR

A. 

Remove plastic wrap and cardboard packaging

 from door. DO NOT remove plastic 

SHIPPINGSPACERS4HESHIPPINGSPACERSWILLHELPKEEPTHEDOORSQUAREDURINGINSTALLATION
$/./4UNLOCKOROPENTHEDOORUNTILITISFULLYFASTENED

Note: If screens, grilles or hardware are removed from the door at this time, label 
them and store them in a protected area.

B. 

Fold out installation fin to 90°.

"ECAREFULNOTTOREMOVEORTEARTHElNCORNERS

Note: If the fin is not at 90°, the door will not line up correctly on the interior.

C. 

Place three 3/8" beads of sealant.

4HElRSTBEADSHOULDBEAPPROXIMATELYFROM

THEEXTERIOROFTHEROUGHOPENINGTHESECONDBEADSHOULDBEPLACEDSOITISUNDERTHE
WOODINTERIORTHRESHOLDOFTHEDOOR0LACEMENTWILLVARYDEPENDINGONWALLTHICKNESS
ANDDOORTYPE0LACEATHIRDBEADOFSEALANTINTHEGROOVEOFTHESILLSUPPORTOR
FROMTHEEXTERIOREDGEOFTHEWOODBLOCKING

  TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLLOWING STEPS.

D. 

Insert the door

FROMTHEEXTERIOROFTHEBUILDING$/./4SLIDETHEBOTTOMOF

the door into the opening. Sliding will damage the sealant lines. Place the bottom 
of the door at the bottom of the opening, then tilt the top into position. Center the 
door between the sides of the opening to allow clearance for shimming, and insert 

ONEROOlNGNAILINTHElRSTHOLEFROMTHECORNERONEACHENDOFTHETOPNAILINGlN

These are used to hold the door in place while shimming it plumb and square.

E. 

Plumb and square door.

0LACESHIMSATEACHHINGEANDLOCKSTRIKELOCATIONBETWEENTHE

DOORANDTHESIDESOFTHEOPENING)NSERTSHIMSINOTHERLOCATIONSASNEEDEDSTARTINGUP
FROMTHEBOTTOMOFTHEDOORTOSQUAREITINTHEOPENING-AKESURETHATTHEREVEALAROUND
THEDOORS ISEQUAL/NDOUBLEDOORSMAKESURETHATPANELSAREEVENACROSSTHEBOTTOM

Note: On center latch double doors the lock strike will not be shimmed since it is 
located in the center of the unit. DO NOT over shim.

F. 

Check the interior reveal.

-AKESURETHEMEASUREMENTFROMTHEINTERIORFACEOFTHEDOOR

to the interior face of the wall is equal at several points around the door.

Note: If the dimensions are not equal, check to make sure the fins are folded out to 90° 
at all points.

Ó 

Ó

&YUFSJPS

Ó

&YUFSJPS

Ó

*OUFSJPS

Ó

Ó

Ó

£

Ó ä Î ä

{ ä x ä

È ä Ç ä

Ó

Î

 -

““

Ó

Содержание 80KM0103








Отзывы: