Pego 200NDIN3RK Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 32

Pego 200NDIN3RK Скачать руководство пользователя страница 9

Chapter 5

– Data programming

DIN NANO 3RK

Page 9

Rev. 01-16

CONTROL PANEL

FRONT KEYPAD

(1)

UP KEY

Increases value / Scrolls up through parameters
Acquires an alarm.
If pressed for more than 5 sec. while viewing the value contained in the Hr1, Hr2 and Hr3
variables (Hour counter of the digital outputs), the information will be reset.

(2)

DOWN KEY

Decreases value / Scrolls down through parameters.

(3)

STAND-BY

If pressed for more than 1 sec., the Stand-by state will alternate with the normal operating
status, and vice versa. In the stand-by state, the system stops and the display will change
the writing OFF with the current view.
If pressed, it switches the display view from °C to Bar and vice versa

.

(4)

SET

Shows the set point
Enables configuration of the set point when pressed together with the Down or UP key.

CHAPTER 5: DATA PROGRAMMING

5.1

5.2

(1)

(2)

(3)

(4)

(5)

(6) (7) (10)

(14)

(8)

(11)

(9)

(12)

(13)

«
...
7
8
9
10
11
...
»

Содержание 200NDIN3RK

































Отзывы:

Нет отзывов