Peg-Perego Viaggio1 Duo-Fix ASIP, Инструкция по эксплуатации

Страница: 28 / 164

28
ensuring that they are snug to the child’s body without
constricting him/her too much. Check that the harness
is not twisted and that the child does not release it.
• This car seat is not intended for prolonged periods of
sleeping.
• Do not leave the car seat in the vehicle when exposed
to the sun. Some parts might heat up and be harmful
to the delicate skin of the child - check before placing
the child in the seat.
• Do not use the car seat without its fabric cover; this
must not be replaced with one not approved by the
manufacturer since it is an integral part of the car seat
and the safety system.
• Do not use the car seat without the protective shoulder
pads as they are an integral part of the car seat and the
safety system.
• If in doubt refer to the manufacturer or retailer of the
car seat.
• Do not remove the adhesive and stitched labels since
this might make the product non compliant with legal
requirements.
• Do not use the car seat if it has signs of breakage or
missing parts, is second hand, or if it has been subjected
to violent stress in an accident, because it might have
suffered extremely dangerous structural damage.
• Do not modify the product.
• For any repairs, replacement parts and information
about the product, contact the after-sales assistance
service. Contact information is provided on the last
page of this manual.
• The car seat should always be secured in the vehicle,
even when the child is not present. In the event of
sudden braking, it could injure the passengers.
• Do not use this car seat after 7 years from the date
of production indicated on the structure. The natural
ageing of the materials may mean that it is no longer
compliant with standards.
• Do not use accessories not approved by the
manufacturer or by the competent authorities.
Instructions for use
UNIVERSAL CATEGORY - Belted
Fastening with seatbelts
1• Place the Viaggio 1 Duo-Fix K TT car seat in a forward-
facing position, as shown in the figure.
2• To make it easier to pass the vehicle’s seatbelts through
the back of the car seat, it is necessary to recline the
seat as far as possible by operating the handle, as
shown in the figure.
3• Pass the vehicle’s seatbelt between the frame and the
body of the car seat.
4• The lap strap must pass through the lower opening
marked in red. Fasten the seatbelt, ensuring that it
clicks into place.
5• Check that the lap strap has passed through the lower
openings marked in red and tighten it.
6• Bring the car seat back to the upright position by
pulling the handle below the seat (Fig. a) and pushing
the car seat as shown in the figure (Fig. b).
7• To finish securing the car seat to the vehicle, use the
Steady Fix device: open the hook and pass the diagonal
strap through it, ensuring that it is taut and not twisted
(Fig. a). Close the tongue (Fig. b).
8• IMPORTANT: Take hold of the seatbelt and pull
it firmly upwards to fit the Viaggio 1 Duo-Fix K TT
more closely to the seat of the vehicle (Fig. c).
Once the procedure is complete, it is possible to recline
the car seat to the desired position (see point 2).
Instructions for use
UNIVERSAL CATEGORY - Isofix & Top
Tether
Fastening with Isofix & Top Tether
9• Recline the car seat to the lowest position by operating
the handle, as shown in the figure.
10• Press the adjuster located inside the base, as shown in
the figure, to extract the Isofix connectors.
11• Open the rear panel and extract the Top Tether (TT).
When the Top Tether hook is not in use, place it back
inside the panel and fasten it as shown.
12• To fasten the car seat’s ISOFIX connectors to the vehicle
seat’s ISOFIX anchors, press sideways on both sides of
the body until they click into position, as shown in the
figure.