Peek Traffic 625X Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

Peek Traffic 625X Скачать руководство пользователя страница 10

10

Output Configuration Options

Presence

means the relay will be energized the entire

time a metal mass is within the field generated by the
loop. The 625X has the ability to provide two presence
outputs. Relay 2 can be set for presence or pulse.

Relay 1 is always presence (pins 5 & 6, yellow and
blue wires), however Relay 2 on the 625X can be
assigned to one of several output configurations.

Relay 2 (pins 3 & 9, Orange and Red wires) can be set
for presence using the switches on the back panel. Set
switch 3 to OFF and switch 2 to ON

Pulse on Entry

means that the relay 2 will be ener-

gized as soon as a metal mass enters the field gener-
ated by the loop. On the back panel, set switch 3 to
OFF and switch 2 to OFF. This pulse will last 125mS.

Pulse on Exit

means that relay 2 will be energized

when a metal mass has left the loop. Set switch 3 to
ON and switch 2 to OFF. The pulse will last 125mS.

Loop fault output

means the relay will be energized if

there is a current fault (open loop, shorted loop or
greater than a 25% inductance
change.) Set switch 3 to ON
and switch 2 to ON.

3
2
1

ON

Switches 2 & 3 control which
output function of Relay 2 is used.

Switch 1 ON doubles the sensitivity
settings on the front panel

«
...
8
9
10
11
12
...
»

Содержание 625X

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды