manualshive.com logo in svg

Peco Pro 12, Руководство оператора

Поделиться
Скачать
Peco Pro 12 Скачать руководство пользователя страница 8

2-10 Boot To Mower Deck Installation

To mount the boot plates P#(B0538) to the boot 
P#(E1039) use (2) 3/8”-16 x 1” carriage bolts P#(K1182) 
and (2) 3/8”-16 nyloc nuts P#(K1216). Make certain that 
when bolting the boot and boot plate together, that the 
head of the bolt is placed from the inside of the boot. 
This will prevent grass from collecting on the bolts.  To 
install the boot plates and boot to the tractor, lift boot 
plate assembly to a 45 degree angle and slide boot 
plates under the deflector shield hinges on each side. 
See Figure 2-10a thru 2-10b.

Figure 2-10b

2-8 Engine Mount Arm Assembly 

Installation

Slide the engine mount arm assembly P#(A0318) 
(Figure 2-8) into the outer engine mount tube P#(A0600) 
until the hole in the engine mount arm assembly aligns 
with the outer engine mount tube hole. Secure the 
engine mount arm assembly using (1) detent pin 
P#(J0248).

2-9 Engine/Blower/Blade Assembly 

Installation

Place the engine/blower/blade assembly onto the motor 
mount arm assembly (Figure 2-9). Secure the 
engine/blower/blade assembly to the engine mount arm 
assembly by using (4) 5/16"-18 x 1-1/2" hex bolts 
P#(K1157) and (4) 5/16"-18 nyloc nuts P#(K1180).  

Figure 2-8

Detent Pin

Engine Mount
Arm Assembly

Boot

Boot Plate

Deflector 

Hinge

Figure 2-9

(4) 5/16”-18 x 1-1/2” HHCS

(4) 5/16”-18 Flange Nuts

Figure 2-10c

Boot

Boot Plates

  

  

  

  

  

  

  

  

Figure 2-10a

B0538 Boot Plates

Grass Deflector

Shield Hinges

8

Содержание Pro 12





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды