Peavey PV 1 Скачать руководство пользователя

Страница: 7 / 10

Specifications

PV®

PV® 3

RATED OUTPUT POWER @ 120V AC Line:

Stereo mode

4 Ohms, 1 kHz, 1% THD

410 W RMS/chan

630 W RMS/chan

1060 W RMS/chan

8 Ohms, 1 kHz, 1% THD

250 W RMS/chan

370 W RMS/chan

630 W RMS/chan

Bridge mode, mono

8 Ohms, 1 kHz, 1% THD

760 W RMS

1170 W RMS

1900 W RMS

HUM & NOISE:

"A" weighted, reference to rated power @ 8 ohms

better than 88 dB

INPUT SENSITIVITY & IMPEDANCE:

@ rated output power, 4 ohms

1.08 V RMS / 2.87dBu

1.17 V RMS / 3.60dBu

1.26 V RMS / 4.23dBu

Balanced, TRS 1/4” phone jack

10 K Ohms per leg

Balanced, XLR (pin 2 positive)

10 K Ohms per leg

Overall system gain per channel

40X (+32 dB)

DISTORTION:

(THD, typical value)

Stereo mode, both channels driven, 4 Ohms

20 Hz to 20 kHz, 10 dB below rated power

Less than 0.1%

20 Hz to 2 kHz, at full rated power

Less than 0.1%

FREQUENCY RESPONSE:

Stereo mode, both channels driven

+0, -2dB at 1 Watt

12Hz to 35 kHz

DAMPING FACTOR:

(Typical value)

Stereo mode, both channels driven

8 Ohms, 20 Hz - 2 kHz

> 250:1

POWER CONSUMPTION:

Stereo mode, both channels driven

@ 1/8 rated output power, 4 Ohms

450W

680W

600W

TOPOLOGY:

Class

WEIGHT:

40 lbs (18.2 kg)

45 lbs (20.5 kg)

49 lbs (22.3 kg)

FEATURE SET:

All Models (++ indicates each channel)

DDT™

COMPRESSION ++:

Automatic, switchable with LED indicator

COOLING SYSTEM:

Two-speed DC fan, air flow back to front

LOW CUT +:

-3 dB @ 40 Hz, 12 dB per octave

CRO+:

150 Hz, 4-pole Linkwitz-Riley approximation

Electronic balanced; Barrier Strip, XLR, TRS 1/4" (6.3 mm)

CROSSOVER O+:

Low/Thru and High, TRS 1/4"Impedance balanced

AMPLIFIER OUTPUTS:

Speakons for Chan A, Chan B and Bridge; Binding Posts

LED INDI+:

Red, DDT/clipping; Yellow, signal; Red, Thermal Protect; Green, power

AMP PROTECTION:

Full short circuit, open circuit; over-temp thermal; RF; stable into any load

LOAD PROTECTION:

Turn on/off muting, DC (triac crowbar), low-cut filter

MAINS VOLTAGES AVAILABLE

100, 120, 230, 240 VAC, 50-60 Hz

DIMENSIONS:

Height: 3.5” (8.9 cm), Width: 19" (48.3 cm), Depth: 15.5" (38.0 cm)

Specifications subject to change without notice

Содержание PV 1











Результаты поиска

Содержание PV 1

Отзывы:

Похожие инструкции для PV 1

Бренды по названию

Популярные бренды

Peavey PV 1, Руководство по эксплуатации

Результаты поиска

Содержание PV 1

Отзывы:

Похожие инструкции для PV 1

Бренды по названию

Популярные бренды