background image

Page 21

Normal Operation

The Genius 3010/3013/3020 & 3022 Gas Generators are designed specifically to 

minimize operator involvement. Given that the systems are installed as described 

in earlier sections and is serviced in accordance with the specified maintenance 
recommendations (see Service Requirements), then it should simply be a matter of 

turning the Generator on when it is required. 

The Generator will automatically produce the factory set flow and pressure as detailed 

in the Technical Specifications.

On Demand Gas

The generator will produce nitrogen on demand. If the application is operating 
and requires a gas flow, the system it is connected to will supply this to suit the 
requirements of the application. If the application requirement for gas stops, the system 
will also stop, once it has reached its upper set limit in the internal storage tanks. If the 
demand from the application starts again, the system will detect the demand for gas 
and will automatically start again to suit the demand.

Generator Cycling

The Generator is designed for the internal compressors to cycle. This cycling reduces 

the duty (run time) on the compressors. The rate at which they cycle will be dependent 
on the gas required to satisfy the demand of the application. If the application demands 

the maximum gas flow of the Generator, the compressor duty will be higher, (the rest 

period in the compressor cycle will be shorter). If the application demand is lower than 
the maximum gas flow, then the duty on the compressors will decrease, (the rest period 

in the compressor cycle will be longer). If the Generator is installed in an extreme 

environment or is subjected to low supply voltage or high altitude the compressors may 

undergo periods where they do not cycle.

Unusual Operation

If at any time the generator begins to emit excessive noise or vibration, then it should 

be switched off and you should contact Peak Scientific or the Peak Partner from which 
the generator has been purchased.

Содержание Genius 3010






























Отзывы: