manualshive.com logo in svg

Peak Hill Industries IMMOBILIZER SHEEP WORKER, Руководство по эксплуатации

Поделиться
Скачать
Peak Hill Industries IMMOBILIZER SHEEP WORKER Скачать руководство пользователя страница 8

8

ASSEMBLY

1. LOCATION

Place the IMMOBILIZER in a location that allows easy access around the 

machine  and  enough  space  for  all  attachments  including  your  leadup 

system. It will be much harder to move once all attachments are in position

2. LEADUP

• Before ramps there should be at least 8-10 metres of sheep in single file
• Panels 400mm apart works best so sheep cannot turn around
•  Have  the  panels  set  up  so  the  last  sheep  can  be  seen  by  new  sheep 

coming into leadup system
• The more sheep in single file the better
• Keep good access for dogs and people beside the leadup race
• Forcing pen before panels should hold 20-30 sheep
• A holding pen after exiting will help to draw the new sheep in
• If sheep are jumping as they walk into machine. Place an object like a    

200lt drum about 3 metres away from front of machine
• Release sheep into small pens to save time if a sheep needs re-processing

Содержание IMMOBILIZER SHEEP WORKER

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды