manualshive.com logo in svg

Peak Hill Industries IMMOBILIZER SHEEP WORKER, Руководство по эксплуатации

Поделиться
Скачать
Peak Hill Industries IMMOBILIZER SHEEP WORKER Скачать руководство пользователя страница 14

14

10. FLOOR EXTENSION INSTALLATION

The floor extension is used to create a larger floor area and partly cover 

over the rear access module. This allows sheep to be off-center and still be 

able to be weighed

Floor extension can only be used with weigh bars fitted as the floor is 

higher
1.

 Remove the 3/4’’ bolts from bottom of legs on one end

2.

 Lift the legs up off the floor enough to fit the floor extension. Caution, 

machine has hoses/wires connecting both sides so lifting too high may do 

damage

3.

  Slide in floor extension (Side tabs down) aligning with rivets and slots in 

the floor

4.

 Place legs back down and tighten. Bolts tighten into a loose plate under-

neath the machine
*Best fitted to the end without handles
*Be careful with the hoses coming from the floor to inside the legs. Avoid 

damaging or crushing

FIG.12

Содержание IMMOBILIZER SHEEP WORKER

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды