PCM 2008 Catanium CES 6.0L ZR-409 Скачать руководство пользователя

Страница: 66 / 93

L510010-11

Engine performance complaints usually fall under one of the basic headings listed in the Troubleshooting Guide. When
a problem cannot be easily diagnosed, consult a PCM Engines Servicing Dealer for assistance.

Malfunction

Possible Cause

Corrective Action

Engine will not crank with the

Problem with the engine

Contact PCM Engines

starter motor, or cranks slowly.

management

system.

Dealer.

Battery switch turned OFF (if

Turn the battery switch ON.

equipped)

Remote control not in Neutral

Position the remote control exactly

NOTICE:

Battery voltage

position.

in Neutral.

must be AT or ABOVE 10

volts while the engine is cranking

Blown ignition/starter fuse.

Replace the fuse

or the engine management system

will not function.

Loose and/or dirty wiring

Check the battery cables and

connections.

starter circuit wiring. Clean

and tighten all connections.

Repair or replace the damaged

wiring.

Dead Battery

Recharge, test and replace as

necessary.

Engine Cranks - will not

Improper starting procedure.

Refer to “STARTING

start or is hard starting.

ENGINE” in the OPERATING

INSTRUCTIONS

section.

NOTICE:

Battery voltage

No fuel - empty fuel tank

Check the fuel tank level -

must be AT or ABOVE 10

tank(s). Open shut-off valve(s).

volts while the engine is cranking
or the engine management system

Plugged fuel

lters.

will not function.

No fuel to the throttle body (TBI)

Plugged or kinked fuel lines or

or the injectors (MPI)

plugged fuel-tank vent.

Faulty fuel pump - check

electrical

connections.

Faulty

anti-siphon

valve.

Engine

ooded

Open the throttle 100% and crank

the engine. When the engine starts,

immediately return the throttle to

1000

RPM.

Ignition system malfunction

Contact PCM Engines Dealer.

Contaminated fuel

Check fuel for water or other

contamination. If contaminated,

drain and clean the fuel system.

TROUBLESHOOTING - 14

Содержание 2008 Catanium CES 6.0L ZR-409






























































































Результаты поиска

Содержание 2008 Catanium CES 6.0L ZR-409

Отзывы:

Похожие инструкции для 2008 Catanium CES 6.0L ZR-409

Бренды по названию

Популярные бренды

PCM 2008 Catanium CES 6.0L ZR-409, Руководство по эксплуатации и техническому обслуживанию владельца

Результаты поиска

Содержание 2008 Catanium CES 6.0L ZR-409

Отзывы:

Похожие инструкции для 2008 Catanium CES 6.0L ZR-409

Бренды по названию

Популярные бренды