background image

Model Number

1102-05a

STRAIN GAGE LOAD CELL

Revision: E
ECN #: 43815

Performance

ENGLISH

SI 

Measurement Range

25 lb

111 N

[5]

Sensitivity(± 10 %)

2 mV/V

2 mV/V

[6]

Non-Linearity

≤ 0.05 % FS

≤ 0.05 % FS

Hysteresis

≤ 0.05 % FS

≤ 0.05 % FS

Non-Repeatability

≤ 0.02 %RO

≤ 0.02 %RO

Eccentric Load Sensitivity

≤ .25 %/in

≤ .25 %/25.4mm

Resonant Frequency

2.10 kHz

2.10 kHz

Creep(in 20 minutes)

≤ .025 %

≤ .025 %

Static Error Band

≤ .05 % FS

≤ .05 % FS

Environmental

Overload Limit

37.5 lb

167 N

Load Limit(Side Force, F

X

 or F

Y

)

25 lb

111 N

[3]

Load Limit

(Bending Moment, M

X

 or M

Y

)

25 in-lb

2.82 Nm

[3]

Load Limit

(Axial Torque, M

Z

)

35 in-lb

4 Nm

[3]

Temperature Range(Operating)

-65 to +200 °F

-54 to +93 °C

Temperature Range

(Compensated)

+70 to +170 °F

+21 to +77 °C

Temperature Effect on Output(Maximum)

± 0.0015 %Reading/°F

± 0.0027 %Reading/°C

[4]

Temperature Effect on Zero Balance(Maximum)

± 0.0008 %FS/°F

± 0.0015 %FS/°C

[4]

Electrical

Bridge Resistance

700 Ohm

700 Ohm

[1]

Excitation Voltage(Recommended)

10 VDC

10 VDC

[2]

Insulation Resistance

5x10

9

 Ohm

5x10

9

 Ohm

Zero Balance

≤ 1 % FS

≤ 1 % FS

Output Polarity

+Tension

+Tension

Physical

Size (Diameter x Height)

2.75 in x 1.50 in

69.9 mm x 38.1 mm

[7]

Weight

0.67 lb

304 g

Mounting Thread

1/4-28 Female

No Metric Equivalent

Housing Material

Painted Aluminum

Painted Aluminum

Sensing Element

Strain Gage

Strain Gage

Deflection at Full Scale Capacity

0.003 in

0.08 mm

Electrical Connector

PT02E-10-6P

PT02E-10-6P

All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.

NOTES:

[1]Nominal.
[2]Calibrated at 10 VDC, usable 5 to 20 VDC or VAC RMS.
[3]Singularly applied, i.e. no other extraneous loads.
[4]Over compensated operating temperature range.
[5]FS - Full Scale.
[6]RO - Rated Output.
[7]See Outline Drawing 51277 for Complete Dimensions

OPTIONAL ACCESSORIES: 

Model 181-012A PT06A-10-6S(SR)
Model 8311-01-10A CABLE

PCB Load & Torque, Inc.
24350 Indoplex Circle
Farmington Hills, MI 48335
UNITED STATES
Phone: 866-684-7107
Fax: 716-684-0987
E-Mail: [email protected]
Web site: 
http://www.pcbloadtorque.com

OPTIONAL VERSIONS

Optional versions have identical specifications and accessories as listed for the standard 

model except where noted below. More than one option may be used.

Entered: AP

Engineer: PE

Sales: JC

Approved: JSD

Spec Number:

Date: 2/17/2015

Date: 2/17/2015

Date: 2/17/2015

Date: 2/17/2015

18331 

Содержание 1102-05A













Отзывы: