PCchips M925 Series Скачать руководство пользователя

Страница: 8 / 49

Mainboard User’s Manual



One parallel port



One MIDI/game port



Six USB ports (two back-panel ports, onboard USB
headers providing four extra ports: header USB1 and
USB2) — all support

USB 2.0



Audio jacks for microphone, line-in and line-out

BIOS Firmware

This mainboard uses AMI BIOS that enables users to configure
many system features including the following:



Power management



Wake-up alarms



CPU parameters and memory timing



CPU and memory timing

The firmware can also be used to set parameters for different
processor clock speeds.

USB 2.0



Compliant with Universal Serial Bus Specification
Revision 2.0



Compliant with Intel’s Enhanced Host Controller
Interface Specification Revision 0.95



Compliant with Universal Host Controller Interface
Specification Revision 1.1



PCI multi-function device consists of two

UHCI Host

Controller

cores for full-/low-speed signaling and one

EHCI Host Controller

core for high-speed signaling



Root hub consists 4 downstream facing ports with
integrated physical layer transceivers shared by

UHCI

and

EHCI

Host Controller



Support PCI-Bus Power Management Interface
Specification release 1.1



Legacy support for all downstream facing ports

Содержание M925 Series


















































Результаты поиска

Содержание M925 Series

Отзывы:

Похожие инструкции для M925 Series

Бренды по названию

Популярные бренды

PCchips M925 Series, Руководство пользователя

Результаты поиска

Содержание M925 Series

Отзывы:

Похожие инструкции для M925 Series

Бренды по названию

Популярные бренды