background image

  

INDUSTRIAL MONITORING INSTRUMENTATION DIVISION

 

PAGE 4 

 

SENSO

RS AN

D INS

TRUME

N

TATIO

N F

OR MAC

HINE 

CON

DITION M

ONIT

ORIN

G

 

 

description 

 

The meter provides two types of measurements 

 overall acceleration and overall velocity.  In the velocity mode, 

the meter measures in the frequency range of 10 Hz to 1 kHz, and complies with ISO2954 standard.  It measures 

overall RMS velocity to a maximum of two inches per second.  In acceleration mode, the meter measures in the 

frequency range of 50 Hz to 50 kHz.  The maximum overall RMS acceleration reading is 20 g

s.  To toggle 

between acceleration and velocity measurements, use the rocker switch labeled 

ACC/VEL

.

  To turn the unit on, 

move the rocker switch labeled 

0/I/Bias

 to the 

I

 position.  The 

0

 position shuts the unit off, while the bias is a 

momentary toggle for monitoring the bias voltage of the sensor.   

 

The meter provides three input connectors that are located at the top of the unit.  The input for the sensor (labeled 

SENSOR) is a standard BNC Jack.  The headphones can be connected through the 1/8 inch stereo jack (labeled 

with the appropriate symbol), and the input for the recharger (labeled CHARGE) is a 2.5 mm plug.  

 

The unit is powered by a 9-volt alkaline battery which is housed in the battery compartment located at the bottom 

of the meter.  To remove this cover, use a small standard screwdriver, pry the cover up, and the push it up 

towards the top of the meter.  Since the meter is supplied with alkaline batteries, 

DO NOT ATTEMPT TO 

RECHARGE ALKALINE BATTERIES.  IT MAY CAUSE A POTENTIAL FIRE AND/OR EXPLOSION.

 

 

The unit has a low battery indicator on the front panel LCD display.  The indicator will light when the battery 

voltage is approximately 7.5 volts.  Please replace the battery or recharge the rechargeable battery if supplied. 

 

If the optional recharger was purchased,  plug-in the recharger in the appropriate connector located on the top of 

the meter.  Turn unit off, and plug the charger into an electrical outlet.  Recharge the battery for approximately 12 

hours.  

Содержание IMI Sensors 687A02
















Отзывы: