PCB Piezotronics IMI SENSORS 649A04 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 26

PCB Piezotronics IMI SENSORS 649A04 Скачать руководство пользователя страница 14

PAGE 9

SENSO

RS AN

D INS

TRUME

N

TATIO

N F

OR MAC

HINE

CON

DITION M

ONIT

ORIN

G

Programming Software

The sensor can be user-programmed with either of two optional programming kits, Model 600A21 (non-ROHS
compliant) or Model 600A35 (ROHS compliant). Both kits include a USB programmer cable/dongle (Model
600A21 kit includes Model 070A89 cable; Model 600A35 kit includes Model 070A103 cable), software (Model
EE225) and terminal block/integral cable adapter (Model 042M17). The software can also be downloaded from
IMI’s website, www.pcb.com. This software must be installed prior to connecting the sensor to the computer using
the USB programmer cable. The software includes both the drivers and user interface needed for programming
the sensor. During initial installation, you may need administrative rights for the computer in order to install the
drivers. Once installed, administrative rights are not required for use.

Figure 8

– Model 600A21/600A35 USB Programmer Kit

Program Installation

Installing the Software and USB Driver: Insert the software CD provided into the CD drive. The software will start
the installation automatically if your PC is set to auto-install applications. If not, browse the CD and click on
Setup.exe to start the installation process. The default installation directory is C:\PCB\EE225. It is recommended
to use the default setting.

The installer will first install the software and then the WinUSB device driver. This device driver is required for the
programmer software to communicate with the 070A89 or 070A103 USB programmer cable.

The following screens will be displayed when the installer starts. Click the Next button to proceed from step to
step.

Figure 9

– Install Location Screen

«
...
12
13
14
15
16
...
»

Содержание IMI SENSORS 649A04



























Отзывы:

Нет отзывов