PCB Piezotronics 123 Series Скачать руководство пользователя страница 8

Model Number

123B23

ICP® PRESSURE SENSOR

Revision: A
ECN #: 51279

P erfo rm an ce

EN G L ISH

SI

Measurement Range(for ±5V output)

10,000 psi

68,950 kPa

Sensitivity(± 15 %)

0.5 mV/psi

0.07 mV/kPa

Maximum Pressure

15,000 psi

103,420 kPa

Resolution

0.2 psi

1.379 kPa

[1]

Resonant Frequency

≥ 25 kHz

≥ 25 kHz

[2]

Rise Time

≤ 20 µ sec

≤ 20 µ sec

[2]

Low Frequency Response(- 5 %)

0.0005 Hz

0.0005 Hz

Non-Linearity

≤ 1.0 % FS

≤ 1.0 % FS

[3]

En viro n m en tal

Acceleration Sensitivity

≤ 0.002 psi/g

≤ 0.0014 kPa/(m/s²)

Temperature Range(Operating)

-100 to +250 °F

-73 to +121 °C

[4]

Temperature Coefficient of Sensitivity

≤ 0.03 %/°F

≤ 0.054 %/°C

Maximum Flash Temperature

10,000 °F

5,538 °C

Maximum Vibration

2,000 g pk

19,600 m/s² pk

Maximum Shock

10,000 g pk

98,070 m/s² pk

Electrical

Output Polarity(Positive Pressure)

Positive

Positive

Discharge Time Constant(at room temp)

≥ 1,000 sec

≥ 1,000 sec

Excitation Voltage

20 to 30 VDC

20 to 30 VDC

Constant Current Excitation

2 to 20 mA

2 to 20 mA

Output Impedance

≤ 100 Ohm

≤ 100 Ohm

Output Bias Voltage

8 to 14 VDC

8 to 14 VDC

P h ysical

Housing Material

17-4 Stainless Steel

17-4 Stainless Steel

Diaphragm

Invar

Invar

Sealing

Epoxy

Epoxy

Electrical Connector

Integral Cable

Integral Cable

Weight

4.59 oz

130 gm

Helium Flow Rate(at 1,500 psi)

40 scf/hr

1.13 m³/hr

Cable Length

4 ft

1.2 m

Water Flow Rate(at 50 psi)

1.2 gal/min

4.5 L/min

[5]

All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.

ICP

®

 is a registered trademark of PCB Piezotronics, Inc.

OP TION A L  VERSION S

Optional versions have identical specifications and accessories as listed for the standard model except

where noted below. More than one option may be used.

N OTES:

[1]Typical.
[2]With helium flow.
[3]Zero-based, least-squares, straight line method.
[4]Applies to internal amplifer, not to external housing.
[5]See PCB Declaration of Conformance PS023 for details.

Date: 12/23/2020

Date: 12/23/2020

Date: 12/23/2020

Date: 12/23/2020

68595

Entered: LK

Engineer: NJL

Sales: MV

Approved: RPF

Spec Number:

3425 Walden Avenue, Depew, NY 14043

Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: [email protected]

SU P P L IED A C C ESSORIES:

Model 065A15 Seal, .624" OD x .553" ID x .080", brass (3)
Model 065A72 Water cooling tubes (o-ring sealed) (2)
Model 070A08 Cable adaptor (micro 10-32 jack to BNC jack) (1)

Содержание 123 Series










Отзывы: