background image

Page 3

Fig A

Fig B

Fig C

Fig D

Step 5 - Mounting on the door

Step 6 - Fitting the handles

Step 7 - Marking out the strike plate

Step 8 - Fitting the strike plate

Select the short (doors thinner than  3/4”) or long mounting 

screws and cut to length if required.

(door thi 3/6”)

Fit the rubber escutcheons to the front and back plates. 

Present the front and rear lock assembly to the door, locating 

the square drive in its recess and join the two parts together 

with 4 mounting screws.

Fit the two handles, positioning the screw holes to the 

underside and secure with the grub screws provided. 

Check the operation of the lock - See Commissioning checks.

Fig A - Vertical position of the strike plate - Close the door and mark the top and bottom position of the

              latch horizontally across the frame.

Fig B - Horizontal position of the strike plate - Measure the distance from the back edge of the door to

             the flat face of the latch.  (NOT the plunger.)

Fig C - Mark this distance on the frame to show how far back the plate needs to be to hold the door closed.

Fig D - Position the strike plate within these guide lines.  Mark the positions of the fixing screws and draw

             around the ‘cut-out’ in the strike plate.

Chisel out a 5/8” aperture to receive the latch bolt.

Fix the strike plate with one latch screw to the surface of the frame.

FROM THE INSIDE: Gently close the door and check that the latch enters the aperture easily with no 

additional ‘play’ in the frame. Slight adjustment can be made by moving the plate slightly. When satisfied, 

draw around the outline of the strike plate, remove it. Score around the outline and then cut the rebate to 

enable the strike plate to lie flush with the surface.

Fix the strike plate using two latch screws and check the lock operation. Remove the strike plate and 

increase the aperture to accept the strike plate backbox. Now re-fix the strike plate and check the operation 

of the ‘anti-shim’ plunger and the door.

The unit is now fully operational and should be enrolled as soon as possible to preserve battery life.

Содержание Easyprox nano









Отзывы: