Paxar Monarch Pathfinder Ultra Silver 6032 Скачать руководство пользователя

Страница: 34 / 40

6-2

Equipment Manual

Problem Solution

The display does not turn on.

Make sure the power is on.
Switch to a fully-charged battery.

An error code and
corresponding message
appears on the display.

See your System Administrator.

Error Codes

Following are some common error codes you may receive.

Code(s) Description

004 – 005

Supply size is incorrect. Reload the correct supplies.

267 – 271
410 – 413

Communication error. See your System Administrator.

703 – 704

Supply Error. Load supplies or make sure they are loaded
correctly.

750

Printhead is overheated. Turn off the printer to let it cool.

751 – 753

The printer sensed a problem with a mark on the supplies.
Check the supplies to see if they are loaded correctly.

756

The printer is out of supplies. Load supplies.

757

Load supplies. The calibrated supply length differs by plus
or minus .25 inches from the format.

758

Supply error. Check for a label jam. Clear the supply path
or reload supplies.

762

Low battery. Recharge the battery.

763

Waiting to dispense label. Press Enter.

768

Printhead error. See your System Administrator.

790 – 791

The printer is busy or has an error pending. Turn off the
printer. Wait two seconds and turn it back on.

904 – 911

System error. See your System Administrator.

SYSTEM
ERROR
VECTOR ##

System error. See your System Administrator.

If these solutions do not work or you have a problem or error code not listed,
see your System Administrator or call Service at the number listed on the
back of this manual

Содержание Monarch Pathfinder Ultra Silver 6032








































Результаты поиска

Содержание Monarch Pathfinder Ultra Silver 6032

Отзывы:

Похожие инструкции для Monarch Pathfinder Ultra Silver 6032

Бренды по названию

Популярные бренды

Paxar Monarch Pathfinder Ultra Silver 6032, Руководство по эксплуатации оборудования

Результаты поиска

Содержание Monarch Pathfinder Ultra Silver 6032

Отзывы:

Похожие инструкции для Monarch Pathfinder Ultra Silver 6032

Бренды по названию

Популярные бренды