background image

 

Page 12 of 12 

 

WILO

 PUMPS 

 

 

Limited Warranty

 

 

All 

Classic Star

 and 

Circo Star

 circulator pumps manufactured by 

WILO

 AG are warranted to the original user only 

to be free of defects in materials and workmanship for a period of 30 months from the date of manufacture or 24 
months from the date of installation, whichever expires first. 

WILO

’s liability under this warranty shall be limited to 

repairing  or  replacing  at 

WILO

’s  option,  without  charge,  FOB  the  closest 

WILO

  distributor  or  service  depot,  any 

Classic Star 

or

 Circo 

Star pump. 

WILO

’s liability will be limited to the replacement or repair of the product. 

WILO

 will not be  liable for any costs of 

removal,  installation  or  transportation  or  any  other  charges  which  may  arise  in  connection  with  a  warranty  claim. 
Limitation of liability may not be allowed in some regions. Please contact local representative for interpretation. 

WILO

 warrants that its products are free from defects in manufacture. 

WILO

 will not be liable for damage or wear 

to  products  caused  by  misapplication  of  the  products,  improperly  maintained  systems,  accident,  abuse,  misuse, 
unauthorized  alteration  or  repair,  or  if  the  product  was  not  installed  in  accordance  with 

WILO

’s  published 

installation and operation instructions. Please visit www.WILO-NA.com for a copy of our installation and operation 
instructions. 

All claims under this warranty must be returned to an authorized 

WILO

 distributor for processing along with proof of 

purchase,  installation  date  and  replacement  date.  A 

WILO

  authorized  distributor  will  then  contact 

WILO

  for  final 

product evaluation and processing. 

WILO

  will  not  be  liable  for  any  damages  that  may  arise  through  product  failure.  There  are  no  express  or  implied 

warranties  beyond  those  warranties  described  or  referred  to  above.  Limitation  of  liability  may  not  be  allowed  in 
some regions please contact local representative for interpretation. 

WILO 

 

Important note 

These installation and use instructions have been designed carefully to the best of our knowledge and belief.   The illustrations used 
are to be considered as conceptual.   
Please note tha

t due to the risk of editor’s errors and misprints no responsibility is accepted for the correctness as regards content. 

Use of information contained in these instructions is made at the user’s risk. The editor declines any liability for persons, property 
damage or especially direct, indirect, immediate or subsequent pecuniary loss resulting from improper, incomplete or wrong 
statements, details or instructions. 

Содержание FlowCon FA













Отзывы: