Pavilion GHQ-C3201WX-FF PB US Скачать руководство пользователя

Страница: 13 / 84

3 Choosing an Installation Location

Locate the vent terminal and make sure there

are no obstacles around the termination for

exhaust to accumulate or be obstructed.

Do not enclose the termination with corrugated

metal or other materials.

Carbon monoxide poisoning or fire may occur

as a result.

DANGER

• Avoid places where fires are common,

such as those where gasoline, benzene and

adhesives are handled, or places in which

corrosive gases (ammonia, chlorine, sulfur,

ethylene compounds, acids) are present.

If you do not follow the above, a fire or

explosion may result causing property

damage, personal injury or death.

• Avoid installation in places where dust or

debris will accumulate.

Dust may accumulate and reduce the

performance of the fan of the appliance.

This can result in incomplete combustion.

• Avoid installation in places where special

chemical agents (e.g. hair spray or spray

detergent) are used.

Ignition failures and malfunctions may occur

as a result.

• Do not install this Combi Boiler in a

recreational vehicle or on a boat as this may

be a Carbon Monoxide Poisoning Hazard.

• The manufacturer does not recommend

installing the Combi Boiler in an attic due to

safety issues.

If you install the Combi Boiler in an attic:

- Make sure the appliance will have enough

combustion air and proper ventilation.

- Keep the area around the Combi Boiler

clean. Dust may accumulate and reduce the

performance of the fan of the appliance.

This can result in incomplete combustion.

- A drain pan, or other means of protection

against water damage, is required to be

installed under the Combi Boiler in case of

leaks.

WARNING

Outdoor installation

• The Combi Boiler is designed for either

indoor or outdoor installation. For

information about outdoor installation,

contact Pavilion Customer Center at https://

www.peerlessboilers.com/ or 1-855-443-

8468.

Never install it in a bathroom, it may be

damaged or a fire may be caused.

Do not install in the following places

• A location where it is not free from obstacles

and stagnant air.

• Near staircases or emergency exits.

• A place where it may be threatened by falling

objects, such as under shelves.

• On common walls as the appliance will make

some operational noises while it is running.

Consideration to the surroundings

• Do not install the Combi Boiler where the

exhaust will blow on outer walls, other

walls or material not resistant to heat. Also

consider the surrounding trees and animals.

The heat and moisture from the Combi

Boiler may cause discoloration of walls and

resinous materials, or corrosion of aluminum

materials.

• Do not locate the vent termination directed

towards a window or any other structure

which has glass or wired glass facing the

termination.

• Take care that noise and exhaust gas will not

affect neighbors.

• If the appliance is installed in a location with

very high humidity, condensate may form

inside the appliance and/or cause incomplete

combustion, damage to the electrical

components, or electric leakage.

Install according to regulations and manual

• Install the Combi Boiler in an area that allows

for the proper clearances to combustible

and non-combustible construction. Consult

the rating plate on the appliance for proper

clearances.

• The Combi Boiler must be installed according

to manual.

• Before installing, make sure that the exhaust

flue termination will have the proper

clearances according to the National Fuel

Gas Code (ANSI Z223.1 - latest edition) or the

Natural Gas and Propane Installation Code

(CSA B149.1).

CAUTION

Choosing an Installation Location

Содержание GHQ-C3201WX-FF PB US





















































































Результаты поиска

Содержание GHQ-C3201WX-FF PB US

Отзывы:

Похожие инструкции для GHQ-C3201WX-FF PB US

Бренды по названию

Популярные бренды

Pavilion GHQ-C3201WX-FF PB US, Руководство по установке

Результаты поиска

Содержание GHQ-C3201WX-FF PB US

Отзывы:

Похожие инструкции для GHQ-C3201WX-FF PB US

Бренды по названию

Популярные бренды