background image

 

Application Note: Configuring the IPLink™ Router for Dual Routed Application

3

 

-

Remote IP address and subnet mask (of the upstream router): 192.168.1.1/24

-

No authentication

 

2620/KK Ethernet port parameters

 

The Ethernet port defines the IP subnet for WAN port 2.

IP parameters

-

IP address: 10.10.9.9

-

Netmask: 255.255.255.0

-

IP subnet: 10.10.9.0/24

-

Gateway route: 192.168.1.2

 

2620/KK WAN Port 2 configurable parameters

 

The second WAN port is configured as follows:

Channelized E1 (G.703/G.704)

-

HDB3 line coding

-

120 Ohm twisted line pair connection

-

Clocking: Not a configurable parameter. WAN port 2 derives clock from WAN 1 to synchronize the 
transmitted signal on WAN port 2. 

-

Time Slots: 1-31

WAN Service parameters

-

Bridged PPP

-

Interface 2: WAN port 2

-

No authentication

 

Initial Configuration

 

Install and configure your IPLink WAN Access Router according to the directions in the 

 

2603 & 2620 IPLink 

Quick Start Guide, 

 

shipped with your router (and available online at www.patton.com/manuals). When cor-

rectly installed: 

The Ethernet port will connect to the same Ethernet LAN as your PC

You can access the web management pages for configuration on the 2620/KK.

 

Access the IPLink Web Management Home Page

 

Access the IPlink Web Management Home page (see 

figure 2

 on page 5) by using a web browser on your PC. 

Enter the IPLink’s IP address and log in to the IPLink.

The IPLink home page is divided into two panes, a 

 

configuration menu pane

 

 on the left, and a 

 

configuration 

information pane

 

 on the right. You will use the 

 

configuration menu pane 

 

to navigate from page to page. You 

will use the 

 

configuration information pane 

 

to view and modify configurable parameters, and to view IPLink 

system status information.

Содержание IPLink 2620/KK













Отзывы: