background image

Industry Canada Notice

37

IpLink 2884 Getting Started Guide 

A • Compliance information

The telephone company may make changes in its facilities, equipment, operations or procedures that could 
affect the operation of the equipment. If this happens the telephone company will provide advance notice in 
order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. 
If the equipment is causing harm to the telephone network, the telephone company may request that you dis-
connect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public 
service commission or corporation commission for information.

Industry Canada Notice 

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is 
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that regis-
tration was performed based on a Declaration of Conformity indicating that Industry Canada technical speci- 
fications were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protec-
tive, operational and safety requirements. The Department does not guarantee the equipment will operate to 
the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company. The equipment must also be installed using 
an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line 
individual service may be extended by means of a certified connector assembly (telephone extension cord). The 
customer should be aware that compliance with the above condition may not prevent degradation of service in 
some situations. Repairs to some certified equipment should be made by an authorized maintenance facility 
designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment mal-
functions, may give the telecommunications company cause to request the user to disconnect the equipment. 
Users should ensure for their own protection that the ground connections of the power utility, telephone lines 
and internal metallic water pipe system, are connected together. This protection may be particularly important 
in rural areas.

CE Declaration of Conformity

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the 
laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec-
ognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the 
above directive is indicated by 

CE

 sign on the device.

The signed Declaration of Conformity can be downloaded at 

www.patton.com/certifications

.

Authorized European Representative

D R M Green

European Compliance Services Limited.

Oakdene House, Oak Road                

Watchfield, Swindon, Wilts  SN6 8TD, UK

Содержание IpLink 2884




















































Отзывы: