manualshive.com logo in svg

Patton electronics 2707RC, Руководство пользователя

Поделиться
Скачать
Patton electronics 2707RC Скачать руководство пользователя страница 21

21

4.0  INSTALLATION

This section describes the functions of the Model 1001R14 rack chassis, 
tells how to install front and rear Model 2707RC Series cards into the 
chassis, and how to connect to the twisted pair interface and the serial 
interface.

4.1  THE MODEL 1001R14 RACK CHASSIS

The Model 1001R14 Rack Chassis (Figure 9, below) has fourteen or six-
teen device card slots, plus a single power supply or dual redundant 
power supplies. Measuring only 3.5” high, the Model 1001R14 is 
designed to occupy only 2U in a 19” rack. Sturdy front handles allow the 
Model 1001R14 to be extracted and transported conveniently.

Figure 11. 

Model 1001R14 Rack Chassis with power supply.

The Rack Power Supply

The power supply included in the Model 1001R14 rack uses the same 
mid-plane architecture as the modem cards. The front card of the power 
supply slides in from the front, and the rear card slides in from the rear. 
They plug into one another in the middle of the rack. The front card is 
then secured by thumb screws and the rear card by conventional metal 

screws.

WARNING

There are no user-serviceable parts in the power sup-
ply section of the Model 1001R14 rack. Voltage set-
ting changes and fuse replacement should only be 
performed by qualified service personnel. Contact 
Patton Electronics Technical support at +1 (301) 975-
1007, via our web site at www.patton.com, or by E-
mail at [email protected], for more information. 

Содержание 2707RC

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды