Patterson Medical Rolyan Smart Handle Pro, Руководство пользователя

Страница: 10 / 18

9
o
When using the accessories such as the door anchor or the extremity cuff, make
sure the accessory is fixed securely b etween the door and the door frame. Always
position the exerciser so that the door opens away from the user . If the door
has a lock, lock it to prevent unexpected door opening by another person. Tug on
the anchor to test for stability before exercise to make sure the anchor does not
slip during exercise.
o
Always use a fresh piece of band for each and every exercise session.
o
To avoid excessively high resistance levels do not use a band that is too short. The
minimum band length between the grips should always be greater than 30cm
(12”).
o
Some brands of exercise bands have a fine wax bloom or powder coating on the
surface (this is to preserve the band) and this coating can affect the grip. Follow
the band manufacturer’s instructions for cleaning any surface contamination
from the band.
o
If the resistance band is slipping from the band clamp, use a light wipe with
alcohol (isopropanol) to clean the inside face of the clamp grips. NEVER APPLY
ALCOHOL OR OTHER ORGANIC SOLVENTS DIRECTLY ON THE BANDS, only on the
clamp grip surfaces. If the clamp mechanism or the clamp faces are damaged in
any way contact your local Rolyan smart handle agent for repair.
o
Do not overstretch bands by more than 3 times its resting length. Example: a
30cm (12”) band should not be stretched to more than 90cm (35”) total length.
o
Do not use the Rolyan smart handle while charging the battery. The system will
beep and automatically turn off when the charge signal is detected
o
Do not tamper with the casing or change/remove any of original parts. This will
VOID the warranty.
o
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC Caution:
1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. This device and its antenna(s) must not be co ‐ located or operating in conjunction with any other
antenna or transmitter.
3. Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
IMPORTANT NOTE : (For Portable Device Configuration)
Federal Communication Commission (FCC) Radiation Exposure StatementThis EUT is compliance with
SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1 ‐ 1999 and had been
tested in accordance with the measurement methods and procedures specified in OET Bulletin 65
Supplement C.
22
HOW TO APPLY THE VARIOUS MODES TO CLINICAL PRACTICE
MODE F ‐ 0: Use to calculate specific exercise intensity dosage (lb, kg, N)
Perform a single repetition through the full range of motion (ROM). The peak force is
displayed, wherever it occurs in the ROM. Multiply that figure by the desired strength
exercise intensity to calculate the target peak force.
*Example ‐ Peak force during the repetition is 22.2 lbs. The exercise intensity is 80%
of 1 RM. Therefore, the exercise ‐ specific resistance dosage is: 22.2 x 0.80
= 17.8 lbs (approximately 18lbs).
MODE F ‐ 1: Use to provide feedback to patient that target force is achieved
This mode enables the patient and you to receive audio (and/or visual) feedback each
time the specific strength exercise resistance dosage is met or exceeded. This mode is
particularly beneficial when the peak force occurs toward the maximum elongation of
the elastic band. Therefore, the patient is prompted to move through his/her full
ROM while exercising.
*Example – Using the same exercise data as in MODE F ‐ 0, chose the color elastic
band that offers around 15 to 20 lbs of resistance. Anchor the ends of the
band so that a single repetition provides 18 lbs of force (NOTE: use Mode
F0 to determine this). Once the band color and length is determined,
using Mode F ‐ 1, enter the peak force target of 18 lbs. Have the patient
exercise to momentary fatigue or for a set number of repetitions (SEE:
Mode F ‐ 2 and Mode F ‐ 3).
MODE F ‐ 2: Use to set repetition targets
Enter the number of repetitions you want your patient to perform for the set of
exercise. This mode is used when you want a particular limit on the number of
repetitions a patient performs and do not want them to exercise to momentary
fatigue.