manualshive.com logo in svg

Patol 5610, Руководство пользователя, Страница: 7 / 16

Поделиться
Скачать
Patol 5610 Скачать руководство пользователя страница 7

Patol Limited 

2.5.5 Detectors 

 

 

a)  Configuration:- 

2 off - Employing reflective cone optical focusing system 

 

 

Coincident fields of view arranged as separate channels 

b)  Field Of View:-   

+5°/-15°(along transit axis path)  +/-38°(across transit path) 

 

Refer to coverage chart in section 

c)  Characteristic 

Spectral Filter :  5 - 14 µm 

 

Sensitivity :  10 - 40 µW 

 

Transit speed : 0.5 to 6 m/s    

 

Response : 80 - 1000 ºC  (170 - 1800 ºF) - See below 

 

NOTE 

#1 

-  Air failure signalled if pressure switch employed. 

Figure 7 indicates the 
correlation between the 
temperature and size of ‘hot 
spot’ anomalies for a typical 
installation to produce one or 
more detector channel 
activations at various trigger 
level settings. 
Exact response is dependant 
on the emissivity factor of the 
monitored material, sensor 
orientation and target speed. 

Specification - Continued

 

2.5.2 

Internal / Maintenance Features  -  Accessed on removal of lid / fascia. 

a)  Indications:-  

2 off Red LEDs - One per sensor channel 

b)  Controls:-     

Test Push-button 

 Reset 

Push-button 

c) Program 

Switch:- Sensitivity :  4 Levels 

(SIL 8 Way)  

Alarm Operation :   ‘OR’ / ’AND’  -  Latching / Auto-Reset 

Auto Reset Timer : 4 Settings  

2.5.3 

Relay Mode - Direct Supply - Relays Enabled 

 

 

a)  Supply Voltage:-  20 to 30 Vdc 

b)  Supply Current:-  Standby - 9 mA 

 

Fire (Alarm) - 24 mA (max) 

c)  Alarm Output:- 

Fire Relay Contact - 1 pole change over - 30 Vdc 500 mA 

  

Normally 

De-energised 

c)  Monitor Output:-  Fault Relay Contact - 1 pole change over - 30 Vdc 500 mA 

 

 

Energised Normal - De-energises on supply / air failure 

#1 

2.5.4 

Low Power Mode - Line current signalling via Fire Alarm Trigger Circuit  

a)  Supply Voltage:-  13 to 30 Vdc 

b)  Supply Current:-  Normal / Standby - 350

μ

A (plus EOL *resistor current) 

 

Fire (Alarm) - 5 mA (plus Alarm Load** resistor current) 

 

Fault - <350 uA 

c)  Alarm Output:- 

Solid state switch - Fit with Alarm Load** resistor 

 

 

Normally Off - Alarm Load switched across supply on fire 

c)  Monitor Output:-  Solid state switch - Fit with EOL *resistor 

 

 

Normally On - EOL open on supply / air failure 

#1

 

0

100

200

300

400

500

600

700

800

900 1000

1

2

3

4

Temperature  Degrees C

250mm Dia.

490 sq cm

100mm Dia.

78 sq cm

50mm Dia.

19.6 sq cm

29mm Dia.

6.45 sq cm

1 sq inch

25mm Dia.

4.9 sq cm

GLOWING / VISIBLE

Fig. 7 

Page  7 of 16 

D1198  -  Issue 1  -  25  September 2013 

Series 5000 - Manual 5610 

Содержание 5610

















Отзывы:

Нет отзывов