background image

PassTime USA 

 

CONFIDENTIAL

 

PassTime GPS Install Guide v 2.5 

Pg. 1 

December 2010 

Overview 

This document defines and specifies the 

GPS

, available under this version: 

 

Model name: PTE-2 – HW Version 1.0 ; SW Version 1.0 

Installation 

Installing the 

GPS 

unit is a simple procedure. All device harness connections will be made in close 

proximity to the steering column in the wiring harness, which runs up the column towards the steering 
wheel. Due to the long-range operational nature of the 

GPS 

unit, all connections should be soldered and 

taped or heat shrunk using the correct soldering and insulation techniques to provide high-quality 
connections. However, you may leave the unit itself out in the open and within your line of sight. The 
quality of your installation is the single most important factor in this product’s success. 

This section covers: 

 

Wiring the PassTime Device Harness into the ignition switch harness. 

(Do not plug the GPS unit 

into the harness until you have made all connections.) 

 

Mounting the 

GPS 

unit. 

Before You Start 

 

Record the 15-digit IMSI number from the unit:   

 

 

Record the make, model, and year of the vehicle in which the unit is being installed: 

Make  

 Model 

 

 Year  

 

Package Contents 

Each 

GPS 

unit contains the following: 

(1) 

GPS 

location unit (

Note: 

Please confirm that the electronic serial numbers (ESNs) on the unit and on 

the bag match.) 

(1)  PassTime Device Harness 

Содержание GPS PTE-2

















Отзывы: