Pass XA25 Скачать руководство пользователя страница 2

WARNING

For your protection please read the following:

Water and moisture: 

 This device should not be used near water ( as per example, near 

a bathtub, washbasin, kitchen sink, laundry tub, wet basement or swimming pool ).  Care 

should be taken such that objects do not have the opportunity to fall, and that liquid is never 

spilled onto or into the device enclosure through openings.

Power Sources: 

 This device must be connected to a mains power source in strict accor-

dance with the supplied  product owners manual.  Please verify that the AC mains voltage 

specified in the product manual matches those requirements indicated on the unit and the 

AC voltage provided to your location by the power company. The product MUST be con-

nected to a MAINS socket outlet with a protective earthing connection.

Power Cords:

  Pass Labs provides a power supply cord that meets all legislated requirements 

for the market in which the product was originally sold.  If  you choose to substitute an af-

ter-market product we urge you to choose one that is fully safety rated by the necessary local 

authority.

Power supply cords should be routed so that they are not likely to be walked on, abraded, or 

pinched by items placed on or against them, paying particular attention to cords where they 

enter plugs or exit from a device.  Never under any circumstance insert a cut or damaged 

power cord into a mains power socket. Cables should never be connected / disconnected 

with equipment powered up.  Failure to heed this warning may damage or destroy equip-

ment.

To Disconnect the Amplifier: 

To safely disconnect the amplifier from the AC you must 

remove the AC power cord from the amplifier.

Ventilation: 

 Power-amplifiers run warm, but you should be able to place your hands on 

them without discomfort.  You must allow for this heat in installation, by providing for free 

air circulation around the product.  Leave a minimun of  6” of  space around the amplifier. 

The ventilation should not be impeded by covering the ventilation openings with items, such 

as newspapers, table-cloths, curtains, etc.

Other Warnings:

No naked flame sources, such as lighted candles, should be placed on the apparatus;

Mulitple speakers: If  mulitple speakers are connected to the monoblocks, the total imped-

ance the amplifiers sees should be 8 ohms or greater.

This amplifier is sutable for tropical climates under 2000m and ambient temperatures of 40 

degress C or less

Servicing:

  To reduce the risk of fire, electrical shock or other injuries, the user should not 

attempt to service the device beyond that which is described in the operating instructions.  

All other servicing must be referred to qualified service personnel.

Содержание XA25









Отзывы: