Pass Laboratories INT-25 Скачать руководство пользователя страница 3

3

Introduction:

Entering their 22nd year of production,  the X and XA power amplifi ers have remained 
at the cutting edge of audio through continuous innovation and refi nement.  At 
Pass we build amplifi ers with excessive output stages, huge heat sinks and massive 
power supplies.  We use the highest quality components in simple linear topologies, 
assembled and tested with great care in Auburn, California.  The measure well and 
sound great.  They are heavy, reliable and expensive.

The new INT-25 offers this at slightly lower power, without frills, at a lower price.  It 
embodies new components and innovative circuits coupled with the best elements of 
the previous generation.

The signal path from input to output has been simplifi ed to fewer components.  
Degeneration, “the other form of feedback” has been eliminated.  The output stage 
consists of a single pair of 800 watt new generation output transistors operating 
push-pull Class A.  We still use the same “New Old Stock” of small power JFETs and 
cascoded MOSFET, in the classic “CFA” voltage gain circuit.  The amplifi er is still DC 
coupled and has no frequency compensation.

The result is faster, lower distortion, lower noise, higher damping and larger Class A 
operating envelope into low impedance loudspeakers, all in a simple 3 stage circuit 
with total of three pair of push-pull gain transistors.

In their ideal state, matched push-pull FETs give perfect “square law” cancellation 
of distortion, an effect somewhat spoiled by degenerative Source resistance used 
to constrain the “personality” of the devices.  The removal of this form of feedback is 
an important element in the performance of the INT-25 and is accomplished by new 
approaches to stabilizing gain and bias of push-pull FETs.

This gives a lower output impedance, more gain, and lower spectral content of 
distortion, as evidenced by measurements (see the specs section), but the more 
important factor is the difference it makes to the music.

We observed this difference some years ago in listening tests.  Degeneration removed 
some of the organic quality to the sound and so became the subject of further 
development work.

The INT-25 measures superbly, but it’s subjective qualities are most special.  In an 
industry where products with great specs are frequently found to be dry and boring, 
this amplifi er breathes life into the music.

Thank you for purchasing this INT-25. It is my sincere hope that you will enjoy it as much 
as we do.
 

 

 

 

 

 

Pass Labs

Содержание INT-25











Отзывы: