-
PMS2000 System
-
Ref.
11/620
PM2024-B
6
2.2 Connettore per controllo remoto
Nel caso si volessero controllare remotamente il
volume e la selezione della BGM, il connettore
REMOTE
dovrà essere utilizzato per collegare il
modulo
PM2024-B
alla scheda accessoria
AC2024
. Per l’utilizzo di questa scheda
opzionale, si rimanda al relativo foglio istruzioni.
Vengono di seguito riportate le connessioni.
3.
MESSA IN FUNZIONE
3.1 Modalità di funzionamento
Il modulo
PM2024-B
può essere utilizzato in
tre differenti modalità:
•
SET 1:
Sistema con consoles analogiche
Le attivazioni di zone saranno impostate in base
ai contatti d’ingresso.
N.B.
Per il funzionamento con basi analogiche,
i contatti abbinati alle zone devono avere
priorità = 0.
•
SET 2:
Sistema con consoles digitali*
La selezione delle zone avviene attraverso i
comandi della CPU
PM2021-B
o
PM2021-V
. I
contatti d’ingresso esterni vengono ignorati.
•
SET 3:
Sistema misto
La selezione delle zone avviene considerando
sia i comandi della CPU
PM2021-B
(
-V
) che lo
stato dei contatti d’ingresso. Nell’eventualità di
chiamate contemporanee verrà valutata la
priorità assegnata al contatto o alla console
digitale.
Nota
: si consiglia di non superare le correnti
massime di targa per le tre tensioni d’uscita
disponibili (5, 12 e 24 V).
*
impostazione di fabbrica.
2.2 Connector for remote control
To control the volume and selection of the
BGM from a remote location, the
REMOTE
connector will have to be used to connect the
PM2024-B
module to an
AC2024
accessory
card. For use of this optional card, see the
relevant instruction sheet. The connections are
shown below, seen from outside.
3.
START-UP
3.1 Operating modes
The
PM2024-B
module can be used in three
different modes:
•
SET 1:
System with analogue consoles
The zone activations will be set on the basis of
the input contacts.
N.B.
In order to function with analogue bases,
the contacts associated with the zones must
have priority level = 0.
•
SET 2:
System with digital consoles*
The zones are selected by means of the
command of the
PM2021-B
or
PM2021-V
CPU. The outside input contacts are ignored.
•
SET 3:
Mixed system
The zones are selected considering both the
commands from the
PM2021-B
(
-V
) CPU and
the status of the input contacts. In the event of
simultaneous calls, the priorities assigned to the
contact or to the digital console will be
considered.
Note
: It is advisable not to exceed the maximum
rated currents for the three available output
voltages (5, 12 and 24 V).
*
factory setting.
Pin
Description
1÷8
Ingresso n°1 ÷ n° 8
9
Prec12 Vcc OUT
10
+12 Vcc (180 mA)
11
+5 Vcc (60 mA)
12
Massa
13
+24 Vcc (60 mA)
14
RS –
15
RS +
Pin
Description
1÷8
Input nr. 1 ÷ nr. 8
9
Prec12 Vdc OUT
10
+12 Vdc (180 mA)
11
+5 Vdc (60 mA)
12
GND
13
+24 Vdc (60 mA)
14
RS –
15
RS +
Содержание PM2024-B
Страница 35: ... PMS2000 System Ref 11 620 PM2024 B 35 ...