Paso Sound Products DMA2015 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 32

background image

PAGE 23

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

PROFESSIONAL AUDIO & SOUND

®

DIGITAL MUSIC AMPLIFIERS

DMA2015/2030/2060/2120

INSTALLING AND USING THE CHIME MODULE PASO MODEL AC1B/DMS

ACCESS TO THE CHIME SOCKET

ACCESS TO THE INTERNAL
CHIME MODULE SOCKET

1)

Remove the Power Cord from the

AC Outlet.

2) Remove the three screws on each
side of the Amplifier securing the Top
Cover to the Chassis.
3) Lift Cover and carefully slide Cover
out towards the rear.
4)

Locate the Socket marked

CHIME MODULE on the Main Printed
Board.

OPTIONAL

EQ CARD

SOCKET

CN 210

EQ MODULE

CHIME MODULE

AMPLIFIER REAR PANEL

OPTIONAL

CHIME CARD

SOCKET

CN 209

CHIME CARD SOCKET

INSTALL THE MODULE

1)

Procure the PASO Model

AC1B/DMS Chime Module

2) Line-up the “

NOSE” of the Module

with the Keyway of the Socket on the
Main Printed Board.
3) Press the Module

gently into the

Socket (do not force).

SETTINGS

PRIOR TO TURNING AMPLIFIER
ON SET THE FOLLOWING:

1) Set the Chime Module Output
Level Control Trimmer approx. 1/4
of a turn clockwise.

2) Replace Amplifier Top Cover.

3) Turn Amplifier ON and momen-
tarily short the Terminal MUTE
(Reference 5) to Terminal G
(ground). The Chime should sound.

4) If the Chime level needs to be
reset, turn Amplifier OFF, remove
cover and adjust the Chime
Trimmer accordingly.

AUX 1

47 Kohm 250 mV

INPUT 3 (MIC-AUX1)

15W RMS

AUX 2

47 Kohm 250 mV

INPUT 4 (MIC-AUX2)

INPUT 1 (MIC)

(AUX 2)

ATTENUATOR

(AUX 1)

ATTENUATOR

INPUT 4

INPUT 3

VOX

SENS

MUTE

DELAY

3 - 60 SEC

8 OHM

2 Watt Max.

SP

INPUT 1 MAY BE
TRANSFORMER

BALANCED

WITH OPTIONAL

MODEL MT250

DMA2015

24 V DC

250 MA

-

+

DMA2015 Chime Activation

5

CHIME ACTIVATION SWITCH

OFF

ON

IMPORTANT NOTE

The PASO Module AC1B/DMS
can be used with the following
PASO Amplifier Models:

DMA2015 - DMA2030
DMA2060 - DMA2120
DMA3060 - DMA3120

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER TOP COVER AND ARE PROVIDED FOR USE BY
QUALIFIED PERSONNEL ONLY. TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SER-
VICING UNLESS YOU ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.

CAUTION !

REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

Fig. 23 - AC1B/DMS CHIME MODULE

Fig. 23A - AC1B/DMS Wiring Diagram

OUTPUT LEVEL TRIMMER

«
...
21
22
23
24
25
...
»

Содержание DMA2015

































Отзывы:

Нет отзывов

Похожие инструкции для DMA2015

Бренд: M2TECH Страницы: 17

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 4

Бренд: Nady Audio Страницы: 12

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 16

Бренд: NAD Страницы: 2

Бренд: Yaesu Страницы: 17

Бренд: Parasound Страницы: 20

Бренд: QSC Страницы: 35

Бренд: Balanced Audio Technology Страницы: 9

Бренд: PowerBass Страницы: 28

Бренд: Goldmund Страницы: 14

Бренд: Focal Страницы: 8

ZOTL40 Reference

Бренд: Linear Tube Audio Страницы: 8

Бренд: K&M Analog Designs Страницы: 8

Бренд: Harley Benton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды